Introducción

Remove all electrical wires from the computer, and lay the computer flat on its screen. The computer should rest on a smooth, padded surface.

Unplug all the cables from the computer, including the power cable. Lay the computer face-down, supporting the neck and base with a soft cloth under the screen.
  • Unplug all the cables from the computer, including the power cable. Lay the computer face-down, supporting the neck and base with a soft cloth under the screen.

Agregar Comentario

Loosen the four Phillips #0 screws.
  • Loosen the four Phillips #0 screws.

Agregar Comentario

Carefully remove the base access panel.
  • Carefully remove the base access panel.

Agregar Comentario

Remove the four 25mm T-15 screws. Remove the four 25mm T-15 screws.
  • Remove the four 25mm T-15 screws.

Agregar Comentario

Open the housing plate. Be gentle with the wires still connected to the logic board  so as not to ruin the cables.
  • Open the housing plate.

  • Be gentle with the wires still connected to the logic board so as not to ruin the cables.

  • A fixed plug connector between the logic board and upper unit will cause some resistance. Pull gently but firmly.

Agregar Comentario

Remove the 2 torx 10mm screws on the EMI shield Carefully remove shield and copper tape Carefully remove shield and copper tape
  • Remove the 2 torx 10mm screws on the EMI shield

  • Carefully remove shield and copper tape

Agregar Comentario

Remove the 4 10mm torx screws attatched to the drive carrier. The drive carrier includes optical drive and hard drive.
  • Remove the 4 10mm torx screws attatched to the drive carrier.

  • The drive carrier includes optical drive and hard drive.

Agregar Comentario

Grasp the carrier with both hands on each side.
  • Grasp the carrier with both hands on each side.

  • Remove the carrier by lifting up and out.

  • Pull gently but firmly. The carrier is meant to fit snugly.

Agregar Comentario

Flip the removed carrier to the right and pull out power cables.
  • Flip the removed carrier to the right and pull out power cables.

Agregar Comentario

Peel back the white paper, revealing the screws that connect the hard drive to the carrier. Remove the 4 T-10 5mm screws connecting the hard drive and frame. (There are 2 screws on each side) Remove the 4 T-10 5mm screws connecting the hard drive and frame. (There are 2 screws on each side)
  • Peel back the white paper, revealing the screws that connect the hard drive to the carrier.

  • Remove the 4 T-10 5mm screws connecting the hard drive and frame. (There are 2 screws on each side)

Agregar Comentario

Slide the hard drive out from the frame and optical drive.
  • Slide the hard drive out from the frame and optical drive.

Agregar Comentario

Remove the four T-10 6mm screws at the sides of the drive.
  • Remove the four T-10 6mm screws at the sides of the drive.

Agregar Comentario

Slide the optical drive out of the carrier
  • Slide the optical drive out of the carrier

Agregar Comentario

Take out the six T-15 screws that hold the fan in place, and remove the fan. Take out the six T-15 screws that hold the fan in place, and remove the fan.
  • Take out the six T-15 screws that hold the fan in place, and remove the fan.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

David Hunter

Miembro Desde 05/10/11

485 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 21-22, Maness Fall 2011 Miembro de Cal Poly, Team 21-22, Maness Fall 2011

CPSU-MANESS-F11S21G22

4 Miembros

13 Guías creadas

We need to show an action shot for step 8 of the REmove Drive Carrier Assembly

Courtney - Contestar

I don't see why it would be necessary... ??

Nicolas Zbinden -

I would like to add; That you may need some thermal past as there is a heat sink that splits in two when you remove the bottom.

substevew - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 4

Últimos 7 Días: 10

Últimos 30 Días: 42

Todo El Tiempo: 4,545