Saltar al contenido principal

iHip Fold-Up Portable Speaker Stand Replacement

Qué necesitas

  1. iHip Fold-Up Portable Speaker Stand Replacement, Removing the battery case cover: paso 1, imagen 1 de 1
    • Use your fingers to slide the battery case cover off in the direction of the arrows.

  2. iHip Fold-Up Portable Speaker Stand Replacement, Cleaning the battery case: paso 2, imagen 1 de 3 iHip Fold-Up Portable Speaker Stand Replacement, Cleaning the battery case: paso 2, imagen 2 de 3 iHip Fold-Up Portable Speaker Stand Replacement, Cleaning the battery case: paso 2, imagen 3 de 3
    • Remove the four AAA batteries. Be sure to check your nearest battery recycling point!

    • Use the detailing brush and a paper towel to remove any corrosion left by previous batteries.

  3. iHip Fold-Up Portable Speaker Stand Replacement, Removing the screws: paso 3, imagen 1 de 2 iHip Fold-Up Portable Speaker Stand Replacement, Removing the screws: paso 3, imagen 2 de 2
    • Unscrew the four outer 1.0 mm screws with a Phillips-Head screwdriver.

    • Screws will be magnetized in position and will require the use of tweezers to be removed.

    • Push down gently on the battery case cover and slide it in the direction the arrows indicate. Remove the batteries.

    • Unscrew the 0.6 mm screw located in the center of the battery case.

    • Keep the 1.0 mm and 0.6 mm screws separate from each other for reassembly.

  4. iHip Fold-Up Portable Speaker Stand Replacement, Removing the back cover: paso 4, imagen 1 de 2 iHip Fold-Up Portable Speaker Stand Replacement, Removing the back cover: paso 4, imagen 2 de 2
    • Remove the back cover carefully; there are many wires that connect it to the device.

  5. iHip Fold-Up Portable Speaker Stand Replacement, Positioning the Stand: paso 5, imagen 1 de 1
    • Pull the stand backwards and around the system.

    • Make sure the stand is positioned perpendicular to the speaker system.

  6. iHip Fold-Up Portable Speaker Stand Replacement, Removing the Stand: paso 6, imagen 1 de 2 iHip Fold-Up Portable Speaker Stand Replacement, Removing the Stand: paso 6, imagen 2 de 2
    • Locate the two small connection points for the stand.

    • Using small needle nose pliers, pinch the end of the stand toward the side of the speaker case.

    • Pop the end of the stand out of the hole in the side of the speaker case.

    • Repeat this step for the opposite side of the stand.

  7. iHip Fold-Up Portable Speaker Stand Replacement, Connecting The New Stand: paso 7, imagen 1 de 1
    • 1. Position the new stand perpendicular to the speaker case.

    • 2. Align the bulbs at the end of the stand with the holes in the side of the speaker case.

    • 3. Gently push the bulbs into the holes of the speaker case.

    • 4. Pull the stand back around the speaker system.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Lisa

Miembro Desde 10/13/14

207 Reputación

2 Guías creadas

Equipo

Clemson, Team 3-4, Benson Fall 2014 Miembro de Clemson, Team 3-4, Benson Fall 2014

CLEM-BENSON-F14S3G4

5 Miembros

8 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 2

Todo El Tiempo: 224