Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a coin to rotate the battery locking screw 90 degrees clockwise.
-
Lift the battery out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard release tabs (shown in yellow) toward you and lift up on the keyboard until it pops free.
-
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (shown in orange) 180 degrees in either direction and try again.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Loosen the four silver Phillips screws that secure the RAM shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Close the display and flip the computer over.
-
Remove the three hex screws using a T8 Torx screwdriver.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or small flathead screwdriver to remove the three rubber feet from the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws on either side of the battery contacts.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push in the thin rims of the lower case surrounding the battery compartment, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
-
-
Retire los siguientes 10 tornillos del protector inferior:
-
Seis Phillips de 3 mm
-
Tres Phillips de 7.5 mm
-
Un Phillips de 14 mm
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single Phillips screw securing the DC-In board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the DC-In cable from the adhesive attaching it to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment.
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 12 mm Phillips in the lower right corner.
-
Four 14.5 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn over the computer and open it.
-
Remove the 3 Phillips screws from the edges of the keyboard area.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails, carefully pry the connector from its socket.
-
Carefully disconnect the multicolored speaker cable from the logic board in the same fashion.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips.
-
Two 4 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the top shield up from the right side, minding the upper left corner which may catch on the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws at the corners of the modem.
-
Remove the two Phillips screws at the corners of the modem.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to pry the modem up from the end nearest the AirPort card to separate its connector from a socket on the logic board.
-
Use your hands to seperate the modem from the modem shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the RJ-11 cable from the end of the modem.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 3 mm Phillips screws securing the AirPort card bracket to the metal framework.
-
Lift the AirPort card retaining bracket up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 3 mm Phillips screws securing the AirPort card to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a spudger, pry up on the AirPort card from the end nearest the hard drive to separate the connector from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
De-route the AirPort antenna cables from above the heat sink and lay them aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 9 screws and 2 nuts from the heat sink:
-
Four 3 mm Phillips from around the fan and the heat sink bracket. The bracket can also be removed at this point.
-
One 11.5 mm (left) and one 4.5 mm (right) Phillips from the plastic fingers of the hinge grill.
-
One 4.5 mm Phillips at the top right corner of the heat sink.
-
Two 6 mm Phillips on the lower left corner and face of the heat sink.
-
Two 4 mm screw nuts with attached springs from either side of the heat sink.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, use a spudger to pry up the heat sink from the left side near the hard drive.
-
While lifting straight up on the hinge grill with your right hand, lift the heat sink with your left hand from the end nearest the hard drive and remove the heat sink assembly from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing the white plastic fingers of the I/O bezel to the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the left side of the computer and slide the I/O bezel away.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Wedge a spudger between the RJ-11 board and the metal framework and slide the board to the left, off of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 4mm Phillips screws securing the hard drive to the metal framework.
-
Carefully lift up the hard drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive enclosure and the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the Reed Switch board connector from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Release the optical drive ribbon clamp as described above. Slide the optical drive ribbon out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Close the display and flip the computer over.
-
Remove the two 5mm Phillips screws securing the battery connector to the metal framework.
-
Lift the battery connector out of the metal framework and disconnect it from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 8 screws:
-
Eight 3.5 mm Phillips.
-
Two 3.5 mm Phillips near the sleep light connector.
-
One 3.5 mm Phillips with a large head in the lower left corner.
-
One 4.5 mm Phillips.
-
From top to bottom, disconnect the inverter, fan, and sleep light cables from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board up from the right side, and slide it up and out of the computer.
-
Cancelar: No complete esta guía.
20 personas más completaron esta guía.