Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a coin to rotate the battery locking screw 90 degrees clockwise.
-
Lift the battery out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard release tabs (shown in yellow) toward you and lift up on the keyboard until it pops free.
-
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (shown in orange) 180 degrees in either direction and try again.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Loosen the four silver Phillips screws that secure the RAM shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Close the display and flip the computer over.
-
Remove the three hex screws using a T8 Torx screwdriver.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or small flathead screwdriver to remove the three rubber feet from the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws on either side of the battery contacts.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push in the thin rims of the lower case surrounding the battery compartment, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
-
Retire los siguientes 10 tornillos del protector inferior:
-
Seis Phillips de 3 mm
-
Tres Phillips de 7.5 mm
-
Un Phillips de 14 mm
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single Phillips screw securing the DC-In board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the DC-In cable from the adhesive attaching it to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment.
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 12 mm Phillips in the lower right corner.
-
Four 14.5 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn over the computer and open it.
-
Remove the 3 Phillips screws from the edges of the keyboard area.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails, carefully pry the connector from its socket.
-
Carefully disconnect the multicolored speaker cable from the logic board in the same fashion.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips.
-
Two 4 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the top shield up from the right side, minding the upper left corner which may catch on the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws at the corners of the modem.
-
Remove the two Phillips screws at the corners of the modem.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to pry the modem up from the end nearest the AirPort card to separate its connector from a socket on the logic board.
-
Use your hands to seperate the modem from the modem shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the RJ-11 cable from the end of the modem.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 3 mm Phillips screws securing the AirPort card bracket to the framework.
-
Lift the AirPort card bracket up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 3 mm Phillips screws securing the AirPort card to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a spudger, pry up on the AirPort card from the end nearest the hard drive to separate the connector from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to disconnect the two antenna cables from the AirPort card.
-
Remove the AirPort card from the computer and set it aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
De-route the antenna wires from above the heat sink, around the RAM socket, and below the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer over.
-
Disconnect the inverter cable from the logic board and deroute it from the metal framework, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer back over.
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Support the display with one hand and remove the single Phillips screw on either side of the hinge (two screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the display up and tilt it backwards, freeing it from the two metal alignment posts holding the hinges in place, and slide it away from you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a 1.5 mm hex screwdriver to remove the two hex screws on either side of the display (four screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your thumbs to slightly separate the rear bezel from the front bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger into the gap between the front and rear bezels.
-
Rotate your spudger until it is parallel to the front face of the display.
-
Run the spudger around the perimeter of the display to separate the rear bezel from its retaining clips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the pieces of readily removable tape from around the perimeter of the display.
-
Carefully remove the aluminum tape covering the display data cable connection.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single screw inserted through the piece of EMI tape near the bottom edge of the display.
-
Use the tip of a spudger to remove the small washer under the screw you just removed.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the aluminum/EMI tape off the cast aluminum frame of the clutch hinges.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing each side of the LCD to the clutch hinge frame (four screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the second of the two Phillips screws securing the clutch cover to the cast aluminum frame of the clutch hinges.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the clutch cover away from the front of the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the pieces of tape covering the display data and microphone cables near the bottom edge of the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the display data cable by pulling its connector away from the socket on the LCD.
-
Remove the display data cable from the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to lift the microphone out of the front bezel.
-
De-route the microphone cable from around the top and side of the display.
-
Cancelar: No complete esta guía.
3 personas más completaron esta guía.