Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Use una moneda para girar el tornillo de bloqueo de la batería 90 grados en el sentido de las agujas del reloj.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the clear plastic tab on the AirPort card and pull toward the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Hold the AirPort card in one hand and use your other hand to remove the antenna cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four silver Phillips screws that secure the RAM shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
-
-
Hay una ranura en la pared del compartimiento de la batería que bloquea la carcasa inferior en su lugar. Use un destornillador pequeño de cabeza plana para levantar el borde inferior de la ranura y tire hacia arriba de la carcasa inferior para liberar la ranura de las pestañas que la sujetan.
-
-
-
Ejecute un spudger a lo largo de la costura entre la minúscula y la mayúscula en la parte frontal de la computadora para liberar las pestañas que bloquean la carcasa inferior. Tire hacia arriba de la carcasa inferior y continúe utilizando el spudger según sea necesario hasta que oiga tres clics distintos.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and away from you until the back tabs pop free.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing the DC-In board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the cable from around the optical drive, removing tape as necessary, and angle the DC-In board out of its compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws from the battery compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn over the computer and open it.
-
Pry up the magnet covering a Phillips screw near the middle of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 7 screws from the edges of the keyboard area.
-
Three 2 mm Phillips along the right edge.
-
One 4.5 mm Phillips underneath where the magnet was.
-
One 6 mm Phillips with a small head in the lower left corner.
-
Two 6 mm Phillips with large heads, one in the upper left corner and one in the middle
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case from the right side and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab. Due to model variatons your trackpad connector may be different from the one pictured.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the upper case about half of an inch and move it so that you can access the power and speaker cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails or a dental pick, carefully pry the connector from its socket. Make sure you're pulling only on the connector and not on the socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the upper case off completely and disconnect the multicolored speaker cable from the logic board. As before, make sure you're pulling only on the connector and not on the socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 15 screws:
-
Fourteen 3 mm Phillips.
-
One 5.5 mm Phillips in the upper left corner.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws at the corners of the modem.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the RJ-11 cable from the top of the modem.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer over.
-
Disconnect the inverter cable from the logic board and deroute it from the metal framework, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer back over.
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the black plastic handle to disconnect the display data cable from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the yellow tape holding the display data cable to the metal framework and remove the single Phillips screw beneath it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Support the display with one hand and remove the single Phillips screw on either side of the hinge (two screws total).
-
When remounting, mind that cables pass under the hinge, not over
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Tilt the display back, freeing it from the two metal alignment posts holding the hinges in place, and slide it away from you.
-
Cancelar: No complete esta guía.
20 personas más completaron esta guía.