Saltar al contenido principal
  1. Este paso está sin traducir. Ayuda a traducirlo

    Use a coin to turn both battery locking screws 90 degrees to the left.
    • Use a coin to turn both battery locking screws 90 degrees to the left.

    • Remove the battery cover.

    • Remove the battery from the computer by pulling up on the plastic tab.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free. Note that the keyboard ribbon is still attached to the logic board, so you cannot completely remove the keyboard yet.
    • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free. Note that the keyboard ribbon is still attached to the logic board, so you cannot completely remove the keyboard yet.

    • If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (between F4 and F5 key) 180 degrees in either direction and try again.

    • Rotate the keyboard away from the screen and rest it face-down on the trackpad area.

  3. Este paso está sin traducir. Ayuda a traducirlo

    If your computer does not have an airport card, you can skip the next two steps.
    • If your computer does not have an airport card, you can skip the next two steps.

    • Grasp the clear plastic tab on the airport card and pull up and toward the display.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Hold the airport card in one hand and use your other hand to remove the antenna cable.
    • Hold the airport card in one hand and use your other hand to remove the antenna cable.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two Phillips screws that secure the RAM shield.
    • Remove the two Phillips screws that secure the RAM shield.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Grasp the wire metal bracket on top of the RAM shield and pull upward to remove the shield.
    • Grasp the wire metal bracket on top of the RAM shield and pull upward to remove the shield.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Pull up the keyboard connector cable by its clear plastic loop.
    • Pull up the keyboard connector cable by its clear plastic loop.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Use a straightened paperclip to manually eject the CD-ROM tray.
    • Use a straightened paperclip to manually eject the CD-ROM tray.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Turn the computer over so that the bottom is facing up.
    • Turn the computer over so that the bottom is facing up.

    • Remove the following Torx screws:

    • Four short T8 Torx near the battery compartment.

    • Two long T8 Torx near the hinges.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Pull the CD-ROM drive tray partly out.
    • Pull the CD-ROM drive tray partly out.

    • Remove the silver Phillips screw from the plastic casing.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Turn the computer over.
    • Turn the computer over.

    • Remove the three Phillips screws.

  12. Este paso está sin traducir. Ayuda a traducirlo

    This is a diagram of the trackpad ribbon clamp connector you will disconnect in the next step.
    • This is a diagram of the trackpad ribbon clamp connector you will disconnect in the next step.

    • 1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).

    • 2) After disengaging the locking bar, slide the cable out of the connector.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.
    • Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.

    • Slide the orange trackpad ribbon out of the clamp.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Do not lift the upper case too far without first disconnecting the audio cable.
    • Do not lift the upper case too far without first disconnecting the audio cable.

    • Push out the rim of the lower case and pull up on the upper case, grasping it just to the left of the optical drive.

    • Repeat the above step on the upper left corner of the upper case, grasping the bottom left corner of the upper case.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the audio cable.
    • Disconnect the audio cable.

  16. Este paso está sin traducir. Ayuda a traducirlo

    Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.
    • Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.

    • You may be thinking you're about to break your upper case. Not to worry - the tabs holding the upper and lower cases together are very strong. Simply apply even pressure and continue to rotate the upper case up and away from the screen until it comes free.

  17. Este paso está sin traducir. Ayuda a traducirlo

    Remove the following Phillips screws:
    • Remove the following Phillips screws:

    • Remove the longer Phillips screw from the middle-rear of the modem shield.

    • Remove the three identical Phillips screws, two on either side of the EMI fingers, and the remaining one on the right side of the modem shield.

    • Remove the larger Phillips screw that secures the EMI fingers to the modem board.

    • Remove the EMI fingers.

  18. Este paso está sin traducir. Ayuda a traducirlo

    Peel the modem shield away from the metal framework below, working from the right front and moving to the left.
    • Peel the modem shield away from the metal framework below, working from the right front and moving to the left.

  19. Este paso está sin traducir. Ayuda a traducirlo

    Remove the Phillips screw from the left side of the modem.
    • Remove the Phillips screw from the left side of the modem.

    • Pry up the right side of the modem.

  20. Este paso está sin traducir. Ayuda a traducirlo

    Lift the modem partially out and disconnect the cable on the left side.
    • Lift the modem partially out and disconnect the cable on the left side.

  21. Este paso está sin traducir. Ayuda a traducirlo

    Remove the Phillips screw from the left hinge.
    • Remove the Phillips screw from the left hinge.

    • Peel up the airport cable from beneath the yellow tape.

  22. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the large display data cable from the logic board and deroute it from the plastic and metal tabs.
    • Disconnect the large display data cable from the logic board and deroute it from the plastic and metal tabs.

  23. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the backlight cable from the logic board and deroute it.
    • Disconnect the backlight cable from the logic board and deroute it.

  24. Este paso está sin traducir. Ayuda a traducirlo

    Remove the three small Phillips screws from the clutch cover.
    • Remove the three small Phillips screws from the clutch cover.

  25. Este paso está sin traducir. Ayuda a traducirlo

    Finally, support the display with one hand while unscrewing the last Phillips screw from the right hinge (push the display gently down to avoid putting pressure on the screw).
    • Finally, support the display with one hand while unscrewing the last Phillips screw from the right hinge (push the display gently down to avoid putting pressure on the screw).

    • Remove the display assembly.

Linea de Meta

9 personas más completaron esta guía.

Documentos Adjuntos

iRobot

Miembro Desde 24/09/09

1 Reputación

647 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 10

Ultimos 30 días: 52

Todo El Tiempo: 13,940