Saltar al contenido principal
Ayuda

iPad 2 GSM Logic Board Replacement

Guía Destacada

Guía Destacada

Esta guía ha sido valorada como excepcionalmente genial por el personal de iFixit.

Replace the Logic Board in your iPad 2 GSM.

Use this guide to replace a damaged logic board.

Parts of this guide were shot with a Wi-Fi model and as such the internals may look slightly different from the cellular model. The procedure is the same for both models except where noted.

Paso 1 Logic Board  ¶ 

Carefully lay the LCD next to the rear panel. Use a plastic opening tool to lift the display data cable lock upwards. Pull the display data cable out of its socket.

Paso 1 Logic Board  ¶ 

  • Carefully lay the LCD next to the rear panel.

  • Use a plastic opening tool to lift the display data cable lock upwards.

  • Pull the display data cable out of its socket.

  • Do not pull the connector upward as you disconnect it from its socket.

Paso 2  ¶ 

Remove the LCD assembly from the rear panel assembly.

Paso 2  ¶ 

  • Remove the LCD assembly from the rear panel assembly.

Paso 3  ¶ 

If present, use a plastic opening tool to help remove the piece of tape covering the end of the dock connector cable. Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board. Peel the dock connector ribbon cable off the rear panel.

Paso 3  ¶ 

  • If present, use a plastic opening tool to help remove the piece of tape covering the end of the dock connector cable.

  • Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board.

  • Peel the dock connector ribbon cable off the rear panel.

Paso 4  ¶ 

Pry the speaker cable connector straight up from its socket on the logic board.

Paso 4  ¶ 

  • Pry the speaker cable connector straight up from its socket on the logic board.

Paso 5  ¶ 

Use the edge of a plastic opening tool to flip up the retaining flap on the headphone jack and front camera cable ZIF socket. Be sure you are prying upward on the hinged retaining flap, not the socket itself.

Paso 5  ¶ 

  • Use the edge of a plastic opening tool to flip up the retaining flap on the headphone jack and front camera cable ZIF socket.

  • Be sure you are prying upward on the hinged retaining flap, not the socket itself.

  • Peel the headphone jack and front camera cable off the rear case.

Paso 6  ¶ 

Pull the headphone jack and front camera ribbon cable straight out of its socket on the logic board.

Paso 6  ¶ 

  • Pull the headphone jack and front camera ribbon cable straight out of its socket on the logic board.

Paso 7  ¶ 

Use the edge of a plastic opening tool to flip up the retainer securing the upper component board cable connector to its socket on the logic board. Pull the connector away from its socket on the logic board. Do not lift the cable upward as you disconnect it.

Paso 7  ¶ 

  • Use the edge of a plastic opening tool to flip up the retainer securing the upper component board cable connector to its socket on the logic board.

  • Pull the connector away from its socket on the logic board.

  • Do not lift the cable upward as you disconnect it.

Paso 8  ¶ 

Remove the three 2 mm Phillips screws securing the SIM card slot to the rear panel.

Paso 8  ¶ 

  • Remove the three 2 mm Phillips screws securing the SIM card slot to the rear panel.

Paso 9  ¶ 

Remove the two 2.9 mm Phillips screws securing the headphone jack to the top edge of the rear panel.

Paso 9  ¶ 

  • Remove the two 2.9 mm Phillips screws securing the headphone jack to the top edge of the rear panel.

Paso 10  ¶ 

Use a plastic opening tool to help pull the headphone jack out of its recess in the top of the rear panel.

Paso 10  ¶ 

  • Use a plastic opening tool to help pull the headphone jack out of its recess in the top of the rear panel.

  • Peel the headphone jack/SIM slot assembly away from the top edge of the communications board.

Paso 11  ¶ 

Remove the two 2.1 mm Phillips screws securing the logic board bracket to the rear case near the digitizer cable socket. Remove the logic board bracket from the rear case.

Paso 11  ¶ 

  • Remove the two 2.1 mm Phillips screws securing the logic board bracket to the rear case near the digitizer cable socket.

  • Remove the logic board bracket from the rear case.

Paso 12  ¶ 

Remove the four 2.6 mm Phillips screws securing the logic and communications boards to the rear panel.

Paso 12  ¶ 

  • Remove the four 2.6 mm Phillips screws securing the logic and communications boards to the rear panel.

Paso 13  ¶ 

Use the edge of a plastic opening tool to gently pry the logic board up from the adhesive securing it to the rear case.

Paso 13  ¶ 

  • Use the edge of a plastic opening tool to gently pry the logic board up from the adhesive securing it to the rear case.

Paso 14  ¶ 

Lift the logic board out from the rear case and rotate it slightly toward the battery.

Paso 14  ¶ 

  • Lift the logic board out from the rear case and rotate it slightly toward the battery.

  • Do not try to completely remove it just yet. There are still three antenna cables attached to it.

Paso 15  ¶ 

Use a plastic opening tool to disconnect both antenna connectors from their sockets on the communications board. Use a plastic opening tool to disconnect both antenna connectors from their sockets on the communications board.

Paso 15  ¶ 

  • Use a plastic opening tool to disconnect both antenna connectors from their sockets on the communications board.

Paso 16  ¶ 

Disconnect the Wi-Fi antenna connector from its socket on the logic board.

Paso 16  ¶ 

  • Disconnect the Wi-Fi antenna connector from its socket on the logic board.

Paso 17  ¶ 

Remove the logic board from the iPad 2.

Paso 17  ¶ 

  • Remove the logic board from the iPad 2.