Saltar al contenido principal
Ayuda

HTC One S Motherboard Replacement

This guide will teach you how to remove the motherboard from an HTC One S.

  • Autor: Jay Miley
  • Tiempo estimado: 20 minutos
  • Dificultad: Moderar

If your motherboard is fried, replace it using this guide.

Paso 1 Motherboard  ¶ 

Remove the three 3.15mm Phillips #00 screws from the turquoise case.

Paso 1 Motherboard  ¶ 

  • Remove the three 3.15mm Phillips #00 screws from the turquoise case.

Paso 2  ¶ 

Using a plastic opening tool, lift the turquoise case from the end near the headphone jack. Using a plastic opening tool, lift the turquoise case from the end near the headphone jack.

Paso 2  ¶ 

  • Using a plastic opening tool, lift the turquoise case from the end near the headphone jack.

Paso 3  ¶ 

Remove the turquoise cover from the phone.

Paso 3  ¶ 

  • Remove the turquoise cover from the phone.

Paso 4  ¶ 

A camera filter is now free to move, so remove it using tweezers. A camera filter is now free to move, so remove it using tweezers.

Paso 4  ¶ 

  • A camera filter is now free to move, so remove it using tweezers.

Paso 5  ¶ 

Use tweezers to lift the yellow polyimide tape that covers the ZIF connectors. Use tweezers to lift the yellow polyimide tape that covers the ZIF connectors. Use tweezers to lift the yellow polyimide tape that covers the ZIF connectors.

Paso 5  ¶ 

  • Use tweezers to lift the yellow polyimide tape that covers the ZIF connectors.

Paso 6  ¶ 

Use the pointed end of a spudger to lift the white tab on the largest ZIF connector opposite the USB connector. Use the pointed end of a spudger to lift the white tab on the largest ZIF connector opposite the USB connector.

Paso 6  ¶ 

  • Use the pointed end of a spudger to lift the white tab on the largest ZIF connector opposite the USB connector.

Paso 7  ¶ 

Use the pointed edge of a spudger to work the ZIF cable out of its connector. To do this, you may have to slowly work both sides until the whole cable is released. To do this, you may have to slowly work both sides until the whole cable is released.

Paso 7  ¶ 

  • Use the pointed edge of a spudger to work the ZIF cable out of its connector.

  • To do this, you may have to slowly work both sides until the whole cable is released.

Paso 8  ¶ 

Repeat the procedure from steps 19 and 20 to remove the cables from the remaining ZIF connectors.

Paso 8  ¶ 

  • Repeat the procedure from steps 19 and 20 to remove the cables from the remaining ZIF connectors.

Paso 9  ¶ 

Using the pointed end of the spudger, pop the antenna cable from its connector on the motherboard. Using the pointed end of the spudger, pop the antenna cable from its connector on the motherboard.

Paso 9  ¶ 

  • Using the pointed end of the spudger, pop the antenna cable from its connector on the motherboard.

Paso 10  ¶ 

Remove the 3.15 mm Phillips #00 screw from the motherboard.

Paso 10  ¶ 

  • Remove the 3.15 mm Phillips #00 screw from the motherboard.

Paso 11  ¶ 

Remove the motherboard from the rest of the phone. Remove the motherboard from the rest of the phone.

Paso 11  ¶ 

  • Remove the motherboard from the rest of the phone.