Saltar al contenido principal
Ayuda

Samsung Galaxy S III Front Panel Assembly Replacement

Guía Destacada

Guía Destacada

Esta guía ha sido valorada como excepcionalmente genial por el personal de iFixit.

Replace the Front Panel Assembly on your Samsung Galaxy S III.

  • Autor: Walter Galan
  • Tiempo estimado: 1 - 2 horas
  • Dificultad: Moderar

Use this guide to replace the front panel assembly.

Paso 1 Front Panel Assembly  ¶ 

Peel the antenna cable up from its channel in the front panel assembly. Do not completely remove the antenna cable, it is still connected to the antenna board.

Paso 1 Front Panel Assembly  ¶ 

  • Peel the antenna cable up from its channel in the front panel assembly.

  • Do not completely remove the antenna cable, it is still connected to the antenna board.

Paso 2  ¶ 

Wedge the tip of a spudger underneath the earpiece speaker and pry the earpiece speaker out of its recess in the front panel assembly. Wedge the tip of a spudger underneath the earpiece speaker and pry the earpiece speaker out of its recess in the front panel assembly.

Paso 2  ¶ 

  • Wedge the tip of a spudger underneath the earpiece speaker and pry the earpiece speaker out of its recess in the front panel assembly.

Paso 3  ¶ 

Use the flat edge of a spudger to peel the top portion of the earpiece/volume buttons/ambient light sensor ribbon cable from the front panel assembly.

Paso 3  ¶ 

  • Use the flat edge of a spudger to peel the top portion of the earpiece/volume buttons/ambient light sensor ribbon cable from the front panel assembly.

Paso 4  ¶ 

Carefully wedge the flat edge of a spudger underneath the ambient light sensor. Continue peeling the earpiece/volume buttons/ambient light sensor ribbon cable up off the front panel assembly.

Paso 4  ¶ 

  • Carefully wedge the flat edge of a spudger underneath the ambient light sensor.

  • Continue peeling the earpiece/volume buttons/ambient light sensor ribbon cable up off the front panel assembly.

Paso 5  ¶ 

Insert the flat edge of a spudger underneath the earpiece/volume buttons/ambient light sensor ribbon cable connector. Gently run the spudger across to continue peeling the the earpiece/volume buttons/ambient light sensor ribbon cable from the front panel assembly.

Paso 5  ¶ 

  • Insert the flat edge of a spudger underneath the earpiece/volume buttons/ambient light sensor ribbon cable connector.

  • Gently run the spudger across to continue peeling the the earpiece/volume buttons/ambient light sensor ribbon cable from the front panel assembly.

Paso 6  ¶ 

Insert a plastic opening tool in between the the buttons ribbon cable and the volume button. Push the volume out of its recess in the front panel assembly. Lift and remove the volume button out of the phone.

Paso 6  ¶ 

  • Insert a plastic opening tool in between the the buttons ribbon cable and the volume button.

  • Push the volume out of its recess in the front panel assembly.

  • Lift and remove the volume button out of the phone.

Paso 7  ¶ 

Wedge the flat edge of a plastic opening tool in between the the earpiece/buttons/ambient light sensor ribbon cable and run it down to loosen the adhesive securing the ribbon cable. Wedge the flat edge of a plastic opening tool in between the the earpiece/buttons/ambient light sensor ribbon cable and run it down to loosen the adhesive securing the ribbon cable.

Paso 7  ¶ 

  • Wedge the flat edge of a plastic opening tool in between the the earpiece/buttons/ambient light sensor ribbon cable and run it down to loosen the adhesive securing the ribbon cable.

Paso 8  ¶ 

Grasp and remove the earpiece/buttons/ambient light sensor ribbon cable out of the phone.

Paso 8  ¶ 

  • Grasp and remove the earpiece/buttons/ambient light sensor ribbon cable out of the phone.

Paso 9  ¶ 

Use a metal spudger to carefully peel the antenna board off the front panel assembly. Lift and remove the antenna board out of the phone. Lift and remove the antenna board out of the phone.

Paso 9  ¶ 

  • Use a metal spudger to carefully peel the antenna board off the front panel assembly.

  • Lift and remove the antenna board out of the phone.

Paso 10  ¶ 

Push the power button out of its recess in the front panel assembly. Remove the power button from the front panel assembly. Remove the power button from the front panel assembly.

Paso 10  ¶ 

  • Push the power button out of its recess in the front panel assembly.

  • Remove the power button from the front panel assembly.

Paso 11  ¶ 

Use the tip of a spudger to pry the vibrator out of its recess in the front panel assembly. Use the tip of a spudger to pry the vibrator out of its recess in the front panel assembly.

Paso 11  ¶ 

  • Use the tip of a spudger to pry the vibrator out of its recess in the front panel assembly.

Paso 12  ¶ 

Use the tip of a spudger to peel the vibrator assembly off the front panel assembly. Use the tip of a spudger to peel the vibrator assembly off the front panel assembly.

Paso 12  ¶ 

  • Use the tip of a spudger to peel the vibrator assembly off the front panel assembly.

Paso 13  ¶ 

Lift and remove the vibrator out of the front panel assembly.

Paso 13  ¶ 

  • Lift and remove the vibrator out of the front panel assembly.

Paso 14  ¶ 

Front panel assembly remains.

Paso 14  ¶ 

  • Front panel assembly remains.

  • If you are replacing the front panel assembly with a new one, don't forget to transfer all the parts you removed to your new front panel assembly.