Saltar al contenido principal
Ayuda

Toshiba Satellite C55-B5302 Keyboard Replacement

This guide will help you replace the keyboard to the Toshiba Satellite C55-B5302 laptop.

  • Autor: Jessie
  • Tiempo estimado: 20 - 25 minutos
  • Dificultad: Moderar

These steps will help guide you to removing the keyboard from your Toshiba Satellite C55-B5302 laptop. This will be more of a time consuming project. Make sure you have all the correct tools.

Secciones

Paso 1 Keyboard  ¶ 

The hard drive is held in place with a soft, blue rubber retainer. The retainer can be disconnected by pulling up on the two tabs at the left side of the hard drive in these images. The hard drive is held in place with a soft, blue rubber retainer. The retainer can be disconnected by pulling up on the two tabs at the left side of the hard drive in these images.

Paso 1 Keyboard  ¶ 

  • The hard drive is held in place with a soft, blue rubber retainer. The retainer can be disconnected by pulling up on the two tabs at the left side of the hard drive in these images.

Paso 2  ¶ 

Gently pull the hard drive away from the connection to remove it from the laptop.

Paso 2  ¶ 

  • Gently pull the hard drive away from the connection to remove it from the laptop.

Paso 3  ¶ 

Using a Phillips #00 screwdriver, remove the three 3 mm screws on the board with white arrows pointing to them.

Paso 3  ¶ 

  • Using a Phillips #00 screwdriver, remove the three 3 mm screws on the board with white arrows pointing to them.

Paso 4  ¶ 

Disconnect the ribbon cables so that you can peel back the keyboard ribbon cable to free it. Remove the 5 mm screw from the chip under the metallic ribbon next to the memory card and disconnect the chip. Use a #0 Phillips screwdriver. Remove the 5 mm screw from the chip under the metallic ribbon next to the memory card and disconnect the chip. Use a #0 Phillips screwdriver.

Paso 4  ¶ 

  • Disconnect the ribbon cables so that you can peel back the keyboard ribbon cable to free it.

  • Remove the 5 mm screw from the chip under the metallic ribbon next to the memory card and disconnect the chip. Use a #0 Phillips screwdriver.

Paso 5  ¶ 

Slide the  circuit board  toward you so that you can  access the keyboard ribbon cable. Separate the keyboard ribbon cable from the plastic it sticks to so that it is free.

Paso 5  ¶ 

  • Slide the circuit board toward you so that you can access the keyboard ribbon cable.

  • Separate the keyboard ribbon cable from the plastic it sticks to so that it is free.

Paso 6  ¶ 

Open the laptop so you can see the keyboard.

Paso 6  ¶ 

  • Open the laptop so you can see the keyboard.

Paso 7  ¶ 

Use one plastic opening tool to slightly pry up the left control key and use another plastic opening tool to push the fasteners out of the way so that the keyboard begins to pop up This is the hardest step and may take some time. You don't want to pop off the control key; just use enough pressure so that the  keyboard will come up past each fastener when it gets the chance.

Paso 7  ¶ 

  • Use one plastic opening tool to slightly pry up the left control key and use another plastic opening tool to push the fasteners out of the way so that the keyboard begins to pop up

  • This is the hardest step and may take some time. You don't want to pop off the control key; just use enough pressure so that the keyboard will come up past each fastener when it gets the chance.

Paso 8  ¶ 

Pull the keyboard out. You may have to keep the ribbon cable from sticking to components so that it can come free.

Paso 8  ¶ 

  • Pull the keyboard out.

  • You may have to keep the ribbon cable from sticking to components so that it can come free.