Saltar al contenido principal
Ayuda

Dell Inspiron 14 3467 Base Cover Replacement

Guía Contribuida Por Miembros

Guía Contribuida Por Miembros

Un miembro increíble de nuestra comunidad escribió esta guía. No está supervisada por el personal de iFixit.

  • Autor: darrius
  • Tiempo estimado: 15 - 25 minutos
  • Dificultad: Fácil

How to remove and replace the Base Cover.

Paso 1 Turning over the Computer  ¶ 

WARNING: Before working inside your computer, read the safety  information that shipped with your computer and follow the steps in Before Working Inside Your Computer.  After working inside your computer, follow the instructions in After Working Inside Your Computer.

Paso 1 Turning over the Computer  ¶ 

Paso 2 Remove the Screws  ¶ 

Remove the eight screws that secure the base cover to the palm-rest assembly.

Paso 2 Remove the Screws  ¶ 

  • Remove the eight screws that secure the base cover to the palm-rest assembly.

Paso 3 Removing the Screws  ¶ 

Remove the two screws that secure the base cover to the palm-rest assembly.

Paso 3 Removing the Screws  ¶ 

  • Remove the two screws that secure the base cover to the palm-rest assembly.

Paso 4 Removing the screws  ¶ 

Remove the three screws that secure the base cover to the palm-rest assembly.

Paso 4 Removing the screws  ¶ 

  • Remove the three screws that secure the base cover to the palm-rest assembly.

Paso 5 Turning the Computer over  ¶ 

Turn the computer over, and open the display.

Paso 5 Turning the Computer over  ¶ 

  • Turn the computer over, and open the display.

Paso 6 Removing the Screws  ¶ 

Remove the three screws  that secure the base cover to the palm-rest assembly.

Paso 6 Removing the Screws  ¶ 

  • Remove the three screws that secure the base cover to the palm-rest assembly.

Paso 7 Disconnecting the Optical-Drive Cable  ¶ 

Open the latch, and disconnect the optical-drive cable from the system board.

Paso 7 Disconnecting the Optical-Drive Cable  ¶ 

  • Open the latch, and disconnect the optical-drive cable from the system board.

Paso 8 Turning the Computer Over  ¶ 

Close the display, and turn the computer over

Paso 8 Turning the Computer Over  ¶ 

  • Close the display, and turn the computer over

Paso 9 Prying the Base Cover  ¶ 

Using a plastic scribe, pry the base cover off the palm-rest assembly.

Paso 9 Prying the Base Cover  ¶ 

  • Using a plastic scribe, pry the base cover off the palm-rest assembly.

Paso 10 Lifting the Base Cover  ¶ 

Lift the base cover off the palm-rest assembly.

Paso 10 Lifting the Base Cover  ¶ 

  • Lift the base cover off the palm-rest assembly.

Paso 11 Release the Optical-Drive Interposer  ¶ 

Release the optical-drive interposer from the tabs, and remove it from the base cover.

Paso 11 Release the Optical-Drive Interposer  ¶ 

  • Release the optical-drive interposer from the tabs, and remove it from the base cover.

Paso 12 Sliding the Optical-Drive  ¶ 

Slide the optical-drive interposer into the tabs on the NEW base cover and snap it into place.

Paso 12 Sliding the Optical-Drive  ¶ 

  • Slide the optical-drive interposer into the tabs on the NEW base cover and snap it into place.

Paso 13 Placing the Base Cover  ¶ 

Place the base cover on the palm-rest assembly and route the optical-drive cable through the slot on the palm-rest assembly.

Paso 13 Placing the Base Cover  ¶ 

  • Place the base cover on the palm-rest assembly and route the optical-drive cable through the slot on the palm-rest assembly.

Paso 14 Sliding the Tabs  ¶ 

Slide the tabs on the base cover into the slots on the palm-rest assembly, and snap the base cover into place.

Paso 14 Sliding the Tabs  ¶ 

  • Slide the tabs on the base cover into the slots on the palm-rest assembly, and snap the base cover into place.

Paso 15 Sliding the Optical-Drive Cable  ¶ 

Slide the optical-drive cable into the connector on the system board and press down the latch to secure the cable.

Paso 15 Sliding the Optical-Drive Cable  ¶ 

  • Slide the optical-drive cable into the connector on the system board and press down the latch to secure the cable.

Paso 16 Placing the Screws  ¶ 

Replace the three screws (M2x5) that secure the base cover to the palm-rest assembly.

Paso 16 Placing the Screws  ¶ 

  • Replace the three screws (M2x5) that secure the base cover to the palm-rest assembly.

Paso 17 Turning over the Computer  ¶ 

Close the display, and turn the computer over.

Paso 17 Turning over the Computer  ¶ 

  • Close the display, and turn the computer over.

Paso 18 Replacing the Screws  ¶ 

Replace the three screws (M2x2) that secure the base cover to the palm-rest assembly.

Paso 18 Replacing the Screws  ¶ 

  • Replace the three screws (M2x2) that secure the base cover to the palm-rest assembly.

Paso 19 Replacing the Screws  ¶ 

Replace the two screws (M2x5) that secure the base cover to the palm-rest assembly.

Paso 19 Replacing the Screws  ¶ 

  • Replace the two screws (M2x5) that secure the base cover to the palm-rest assembly.

Paso 20 Replacing the Screws  ¶ 

Replace the eight screws  that secure the base cover to the palm-rest assembly.

Paso 20 Replacing the Screws  ¶ 

  • Replace the eight screws that secure the base cover to the palm-rest assembly.