Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the device on it side with the buttons away from you.
-
Using the SIM Card Eject Tool, insert the narrow end into the ejection hole.
-
Press firmly into the hole until the SIM card tray pops out far enough to grab with your fingers.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the tray out with your fingers .
-
Remove the SIM card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the one T2 screw from the side of the phone near where the SIM card tray was.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a plastic opening tool into the space where the SIM card tray used to be.
-
Gently pry the back away form the phone frame until you hear and audible click of the back separating.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the plastic opening tool into the space you created between the phone back and frame.
-
Slide the plastic opening tool along the outside of the phone, underneath the back, to separate the rest of the clips holding the back onto the frame.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the back over to the side, being careful not to damage the fingerprint sensor ribbon cable.
-
Use a plastic opening tool to separate the fingerprint sensor from the back of the phone.
-
Set the phone back aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 6 silver 2.9mm screws from the back of the phone with a JIS #000 bit.
-
Remove the 11 black 3.5mm screws with the same JIS #000 bit.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the phone over, with the screen up.
-
Insert the opening tool between the screen and the silver trim that surrounds it.
-
Run the plastic opening tool around the circumference of the phone to separate the clips of that hold the trim to the frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the phone back over, with the screen down.
-
Lift the trim piece off of the phone and set aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a plastic opening tool, separate the fingerprint ribbon connector from the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a set of tweezers, pull off the small piece of tape on top of the ribbon cable connector on the left side of the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool or spudger to scrape the glue away from the ribbon cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a plastic opening tool or spudger, open the zip connection by prying up on the right (black) side of the connector.
-
Using the tweezers, carefully pull the the ribbon cable out of the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a plastic opening tool or tweezers, pry the edge of the button strip away from the phone.
-
Once all of the buttons are free, the whole assembly should simply lift out.
-
Cancelar: No complete esta guía.
5 personas más completaron esta guía.
3 comentarios
can you do a videomplz
I need help. When I plug the charger in it would turn on but since the power button was broken I had to buy a new one and today I had received it. Now I did everything correctly however, on step 14 I didn't use tweezers since I didn't have any to remove the ribbon and the ribbon didn't get affected but on top where the ribbon goes in at broke. It should still turn on. So I put everything back and put the charger in and it charges but it doesn't show that it's charging now. And whenever I hold the power button the light twitches but the phone doesn't turn on or even show the percent of the battery which never did that until now. Did I do something wrong? Current trying to redo everything.
I can’t believe I was able to fix this thing! Amazing. Ordered the button, took it apart with my kit and rebuilt it. Not to mention I took apart my Mac ProBook and fixed that too!! Apple Store - It’s hopeless, your data is gone forever. Get a new machine. Best Buy - It’s hopeless, your data is gone forever. Get a new machine.
Nope!