Repara tus cosas Únete a la comunidad Tienda

Xbox Power Board Replacement

Introducción

This is the guide to replacing the unit that deals with power in the Microsoft Xbox. This is potentially the cause of the Xbox not turning on.

Qué necesitas

  1. Xbox Power Board Replacement, Hard Drive: paso 1, imagen 1 de 1

    • Make sure your Xbox is safely unplugged and is laying on a flat, stable surface.

    Editar

  2. Xbox Power Board Replacement: paso 2, imagen 1 de 1

    • Turn the Xbox over to reveal the four rubber feet.

    • Use a metal spudger to pry off the four rubber feet.

    Editar

  3. Xbox Power Board Replacement: paso 3, imagen 1 de 2 Xbox Power Board Replacement: paso 3, imagen 2 de 2

    • There are 2 more screws hidden under the two labels on the bottom of the case.

    • You can either remove the labels or simply feel for the screw holes through the labels and then cut or punch a hole through them.

    Editar

  4. Xbox Power Board Replacement: paso 4, imagen 1 de 1

    • Remove the six T20 Torx screws securing the top cover to the bottom cover.

    Editar

  5. Xbox Power Board Replacement: paso 5, imagen 1 de 2 Xbox Power Board Replacement: paso 5, imagen 2 de 2

    • Once the bottom and top shells are no longer attached, carefully turn the Xbox right-side-up, lift and remove the top cover.

    Editar

  7. Xbox Power Board Replacement: paso 6, imagen 1 de 2 Xbox Power Board Replacement: paso 6, imagen 2 de 2

    • Remove the three 3 mm T10 screws securing the hard drive to the Xbox.

    • There is one screw on the rear left side of the hard drive that is only visible when the IDE ribbon cable is lifted up. The other two are at the front right and left sides of the hard drive.

    • The screw on the lower left corner of the disk drive is not in the hole that it appears to be in, but rather just closer to the corner.

    Editar

  8. Xbox Power Board Replacement: paso 7, imagen 1 de 2 Xbox Power Board Replacement: paso 7, imagen 2 de 2

    • Free the hard drive power cable from the carrier for sufficient slack to lift the hard drive out.

    • Lift the plastic hard drive carrier out of the Xbox case.

    Editar

  9. Xbox Power Board Replacement: paso 8, imagen 1 de 3 Xbox Power Board Replacement: paso 8, imagen 2 de 3 Xbox Power Board Replacement: paso 8, imagen 3 de 3

    • Remove the four 3.4 mm T15 Torx screws from the plastic hard drive carrier (two screws per side).

    • Carefully remove the hard drive from the plastic carrier. Gentle rocking will see the hard drive come out quite easily.

    Editar

  10. Xbox Power Board Replacement: paso 9, imagen 1 de 2 Xbox Power Board Replacement: paso 9, imagen 2 de 2

    • Pull both the hard drive data ribbon cable and the power cable straight up from the hard drive.

    • They may be firmly seated, so be careful trying to remove them. DO NOT pull the wires as you may damage the cable assembly.

    Editar

  11. Xbox Power Board Replacement, Disc Drive: paso 10, imagen 1 de 3 Xbox Power Board Replacement, Disc Drive: paso 10, imagen 2 de 3 Xbox Power Board Replacement, Disc Drive: paso 10, imagen 3 de 3

    • Remove the disk drive. It should come right out.

    • Unplug the ribbon cable and yellow cables from back of disk drive.

    Editar

  12. Xbox Power Board Replacement: paso 11, imagen 1 de 1

    • Pry back the black plastic tabs around the disk drive in order to remove it from its housing. Once removed, set the drive aside.

    • ONLY REMOVE IF DEAD!

    Editar

  13. Xbox Power Board Replacement, Power Board: paso 12, imagen 1 de 1

    • Unplug the multi-colored power cord from the motherboard. It is in there pretty tightly, so it may take some effort.

    Editar

  14. Xbox Power Board Replacement: paso 13, imagen 1 de 2 Xbox Power Board Replacement: paso 13, imagen 2 de 2

    • Using T10 Torx screwdriver, remove two 3mm screws from the tan power supply board.

    Editar

  15. Xbox Power Board Replacement: paso 14, imagen 1 de 1

    • Remove the power supply and set it aside. It should lift right out.

    • Be very careful not to touch the copper coil or capacitors on the power supply. They may shock you.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

31 personas más completaron esta guía.

Autor

con 6 otros colaboradores

rmarstel

Miembro Desde 10/29/09

5,376 Reputación

5 Guías creadas

Insignias: 15

+ 12 más insignias

Equipo

Cal Poly, Team 18-2, Maness Fall 2009 Miembro de Cal Poly, Team 18-2, Maness Fall 2009

CPSU-MANESS-F09S18G2

3 Miembros

23 Guías creadas

Un comentario

http://www.ebay.com/gds/How-To-Determine...

Utilize the information on this website to determine what Xbox version you have so you know what replacement parts to look for.

Navy Vet 2015 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 7

Ultimos 7 días: 36

Ultimos 30 días: 197

Todo El Tiempo: 31,115