Saltar al contenido principal

Xbox One X Project Scorpio Edition Outer Case Replacement

Qué necesitas

  1. Xbox One X Project Scorpio Edition Outer Case Replacement, Outer Case: paso 1, imagen 1 de 2 Xbox One X Project Scorpio Edition Outer Case Replacement, Outer Case: paso 1, imagen 2 de 2
    • Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.

  2. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 2, imagen 1 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 2, imagen 2 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 2, imagen 3 de 3
    • Using precision tweezers, remove the screw tab located on opposite side of the box.

    • Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.

  3. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 3, imagen 1 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 3, imagen 2 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 3, imagen 3 de 3
    • Orient the case so that the front of the Xbox (the side with the power button) is facing you.

    • Remove the top of the case by sliding the case towards you.

    Bitte auch diesen Schritt überarbeiten. Es wird lediglich das Gehäuse für ca 2-4 Zentimeter nach hinten verschoben, dann sollte bereits das erste Hinterniss kommen, welches man ohne Gewalt nicht bewältigen kann. Hier muss das Gehäuse auf der Rechten Seite angehoben werden, dann lässt sich das Gehäuse ohne Probleme entfernen. Auch beim Zusammenbauen. Erst auf der Linkenseite bis zum ersten Plastik Haken (ca 2-4 Zentimeter vom Ende entfern) anlegen, danach auf der Rechten seite einklicken. Das Gehäuse kann auf der Rechten Seite auch etwas gedehnt werden, dabei geht nichts kaputt.

    Marcel - Contestar

    Please also revise this step. It is only the case for about 2-4 centimeters moved backwards, then should already come the first butt that you can not cope without violence. Here, the housing must be raised on the right side, then the housing can be removed without problems. Also when assembling. First put on the left side until the first plastic hook (about 2-4 centimeters from the end), then click on the right side. The case can also be slightly stretched on the right side, nothing breaks.

    Marcel - Contestar

  4. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 4, imagen 1 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 4, imagen 2 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 4, imagen 3 de 3
    • Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing.

    • Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.

    I feel like someone wanted to use a T9 for everything, but these were T8.

    Christopher McKay - Contestar

    You can use a T8 or T9 for this step. I was able to get all three screws with a T9 but there’s so little difference that both will work.

    Bryan Remely - Contestar

  5. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 5, imagen 1 de 2 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 5, imagen 2 de 2
    • Remove the unscrewed panel from the side of the device by pulling it toward you.

    • Be mindful of the connector, as it is fragile.

  6. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 6, imagen 1 de 2 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 6, imagen 2 de 2
    • Pull the upper edge of the white clip down, and then remove the white connector from the dislocated panel using precision tweezers.

    • Do not force the connector out, as it is fragile. Wiggling may be necessary.

    Unfortunately the manual is not correct here. Above the black slot is a white switch / pen, fold it over with your fingernail, so fold it over to the front. Then the cable can be easily removed without any problems and tweezers. GERMAN: Hier ist die Anleitung leider nicht korrekt. Oberhalb des schwarzen Steckplatzes befindet sich ein weißer Schalter/Stift, diesen mit dem Fingernagel umklappen, also praktisch zu der Vorderseite umklappen. Danach lässt sich das Kabel ohne Probleme und Pinzette einfach abziehen.

    Marcel - Contestar

    Thanks for telling me that

    NR26 -

    Thank you. Had no idea what the !&&* this guy was talking about with the “pull down" part. You flip it downward gently like a flap.

    Get To The Point Already - Contestar

    there seems to be a missing step here. Nowhere are we told to remove the screws on this board.

    adcurtin - Contestar

    It is not necessary to remove the white flat cable. After removing the three gold screws from the board, go to the next steps and in step 9 remove the cover while hold the board against the cover to prevent stress on the white cable.

    Whole Witt - Contestar

    @Whole Witt, I second this. When you get to step 9 to remove the cover, just carefully remove the board, then remove the cover along with the board. You can leave the board in the cover.

    jonathan acosta - Contestar

    this is the worst step microsoft did bout this whole machine. most fragile thing is this right here. !!!!!!!!!!!!!!!!!!

    matt C - Contestar

    ok so the white thing see, just take finger nail. and on the far edge flip it up.. very delicate. putting back together flip down. its the the white plastic thing that moves

    matt C - Contestar

    To reinstall put it back down and push the ribbon into it. it will click into place

    matt C - Contestar

  7. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 7, imagen 1 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 7, imagen 2 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 7, imagen 3 de 3
    • On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws.

    • Remove both of these 7mm screws with a Torx T9 screwdriver.

    • Lift the detached plate off to the side.

    • The plate is still connected to the device.

    These are actually T8. Be careful trying to use a T9.

    Christopher McKay - Contestar

    these have the blue goo on them if you like me got a pile of screws

    matt C - Contestar

    what is the name of this strip it tore on mine how do I get it replaced?

    Ruben Lopez - Contestar

  8. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 8, imagen 1 de 2 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 8, imagen 2 de 2
    • Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.

    These are all T10 on my Scorpio.

    Christopher McKay - Contestar

    These are T10 on the Xbox One X MFR Date 22-OCT-2017. You could get away with T9 and would be careful.

    Richard Lloyd (Tekeek) - Contestar

    My manufacture date is 15-JUN-18 and is not a Scorpio and is still T10. I would not recommend using a T9.

    Bryan Remely - Contestar

    They are t-10 and t-8

    Kellie Ramos - Contestar

  9. Xbox One X Project Scorpio Edition Outer Case Replacement: paso 9, imagen 1 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 9, imagen 2 de 3 Xbox One X Project Scorpio Edition Outer Case Replacement: paso 9, imagen 3 de 3
    • Turn the Xbox over, so that the bottom of the case is on top.

    • Lift the bottom of the case off of the Xbox by pulling it up and toward you.

    I had to slide it forward off of the disc drive a little bit before I could lift up.

    Bryan Remely - Contestar

    When putting this cover back on, lay it flat and slide the case into it, slightly angling the front down so the plastic lugs on the BD-ROM fascia board slide into the slots in the cover You’ll have to push to the left slightly (with the cover flat side down and the front facing you) so as to depress the clip on the left-front side of the cover. You can check that the cover is on correctly by looking at the back of the cover and case and ensuring the screw holes on the cover line up with the case bezel.

    Chris Knight - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

7 personas más completaron esta guía.

Ashley Masuda

Miembro Desde 01/24/18

2,757 Reputación

7 Guías creadas

Equipo

Cal Poly, Team S2-G6, Livingston Winter 2018 Miembro de Cal Poly, Team S2-G6, Livingston Winter 2018

CPSU-LIVINGSTON-W18S2G6

4 Miembros

23 Guías creadas

2 comentarios

Where do you get the outer case from? And if I only want to replace the outer case could I just follow the first 3 steps?

Daniel - Contestar

Following. I need a replacement project Scorpio case. the system I got it from was from Mercari and the guy did a poor job in taking care of the case and I need a top Scorpio case.

Britteny X. Wilson -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 4

Ultimos 30 días: 37

Todo El Tiempo: 5,285