Saltar al contenido principal

Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One

Qué necesitas

  1. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Paquete de baterías: paso 1, imagen 1 de 1
    • Retira la cubierta del paquete de baterías.

    • Retira las baterías.

  2. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Manijas laterales: paso 2, imagen 1 de 2 Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Manijas laterales: paso 2, imagen 2 de 2
    • Recomendamos el uso de un spudger de nylon para este paso. Se muestra un spudger de metal.

    • Sujeta el controlador firmemente para quitar las asas laterales, encajando un spudger en la costura entre la parte delantera y las placas del mango.

    • Levanta la placa lateral alejándola de la placa frontal moviendo el spudger hacia adelante y hacia atrás. Tendrás que hacer esto en toda la costura de la placa lateral.

    Start prying the side plate off underneath the trigger, this makes it easier to disconnect the other clips connecting the side plate to the backplate.

    Brandon - Contestar

    One you take it off, is it possible to click it back in?

    Aiden Bear - Contestar

    As long as you don’t exceed the couple tons you need to take it off you should be able to put it back.

    Brandon -

    getting those handles back on seems impossible, they just dont fit as well, a gap remains even after snapping into place.

    Dont think ill be doing this in the future

    Spoutin Wyze - Contestar

    edit: wiggled the bo9ttom middlewith the handles off and somethign finally “clicked” into place for that extra 1/4 mm for the down arrow on my D-Pad to click back up into place!.

    Spoutin Wyze - Contestar

  3. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Tornillos: paso 3, imagen 1 de 2 Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Tornillos: paso 3, imagen 2 de 2
    • Hay un tornillo escondido en la parte central trasera del mando

    • Utiliza el destornillador para hacer un agujero en el centro, y poder así, quitar el tornillo

    • También puedes quitar la etiqueta si no deseas hacer un agujero en ella

    • Quita los 5 tornillos de 10mm que están en la parte trasera del mando utilizando el TR8 Security Torx Screwdriver.

    i damaged my screws. how do i get the screws out?

    tenzin - Contestar

    wait. i just watched a video guide on ifixit's youtube channel about damaged screws. i'll try those methods.

    tenzin - Contestar

    It's a t8 or t9 security bit btw, I got the top two out with a regular T8, but the bottom two and middle needed a T9 Security bit.

    David Loper - Contestar

    All five faceplate/backplate screws in the controller I disassembled were T8 security fasteners.

    John Dziedzic - Contestar

    Am I doing something wrong because I got the tool it said I needed and got the middle screw out but the others have a bump or something in the center of the screw and it won't fit.

    kolton77 - Contestar

    The T8 is only good for the middle screw on my One S controller. The others require something bigger

    Matej Skelo - Contestar

    These requires SECURITY Torx bits (they have a cannulated hole in the driver). I don't believe the iFixIt branded driver is cannulated but you can buy a set of bits from DeWalt DWAX200 which is overkill but has what you need.

    jhighsmith - Contestar

    The driver that iFixIt sells is cannulated.

    jhighsmith -

    where do you get this dumb ass screw driver

    Jake Zweier - Contestar

    iFixit Store #IF145-027-3

    VauWeh - Contestar

    You can bypass it with a 1.5mm flathead.

    Marianne Sandling - Contestar

    thank you for this. worked for me

    Mr Anderson (Evolluisionist) -

    These screws required a T10, not T8.

    Armand - Contestar

    TR9. A $10 kit from Walmart has the bit/driver in it and extra goodies to make life simple.

    Matt Martin - Contestar

    As weird as it sounds, the top 2 came out for me with a flathead- but the bottom two and the middle one wont

    macybrooksevans - Contestar

    If you damage the middle part of the screws you can still take it out with the same screwdriver.

    Kev God - Contestar

    needed a T8H, not easy to see.

    on a grey green xbox one controller

    Michael - Contestar

    On my 1708 controller there are two internal screws near the rumble motors that need to be removed with a T6 non security bit to remove the back cover.

    teeedubb - Contestar

  4. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Placa trasera: paso 4, imagen 1 de 1
    • Retira la placa posterior.

  5. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Placa frontal: paso 5, imagen 1 de 1
    • Retire la placa frontal.

  6. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Motores de Vibración: paso 6, imagen 1 de 2 Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One, Motores de Vibración: paso 6, imagen 2 de 2
    • Puedes dejar que los motores retumbantes cuelguen libremente de sus enchufes.

    • Desuelda las uniones soldadas mientras sujetas los cables rojo y negro en la placa base superior.

    • Ten cuidado al usar el soldador para no dañar otros componentes o lastimarte.

    • Para obtener información sobre cómo soldar, haga clic aquí.

  7. Sustitución de los Motores de Vibración del Mando (Controlador) Inalámbrico de la Xbox One: paso 7, imagen 1 de 1
    • Retire los motores de ruido.

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

14 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ Francisco Javier Saiz Esteban nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Liam Gow

Miembro Desde 01/22/15

5,284 Reputación

3 Guías creadas

Equipo

Cal Poly, Team 20-15, Maness Winter 2015 Miembro de Cal Poly, Team 20-15, Maness Winter 2015

CPSU-MANESS-W15S20G15

5 Miembros

50 Guías creadas

7 comentarios

Hey I let my motor hang off when I was taking apart my controller and it tore off the motherboard on one side of my controller, is there a way to repair that?

Mark - Contestar

Hi Mark,

Assuming that nothing beyond some solder came off with the wires, you can try resoldering the motor's wires back into place. Make sure to check exactly where they are meant to connect, and not to accidentally solder anything else on the board.

Liam Gow -

What is the positive wire for the rumble pads. I think it might be the reverse of the normall.

metalcka - Contestar

It would be nice to show the positioning of the motors in the frame since they are not symmetrical. The left one has a larger weight.

codekaizen - Contestar

Where can I buy these rumble motors?

Steve Pepe - Contestar

I'm had to de remove the rumble motors from the board temporarily. I didn't take a picture of what it looked like before I de soldered the wires. I know the pads they need to be re soldered to. But don't know in what order. Is there any pictures you know of on how these controllers are wired so I don't solder them into the wrong spot?

Matthew Glenn (Matt) - Contestar

Will it cause issues to simply remove the rumble motors and not reinstall them? I need one controller that cannot vibrate. It'll only be used for a single game that regardless of the settings used (including any special things in an elite controller) it will still f'n vibrate. If it will not cause issued I will mod one of my other controllers.

Thanks in advance

Eliza - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 28

Ultimos 30 días: 121

Todo El Tiempo: 23,141