Saltar al contenido principal

Xbox 360 Wireless Controller Bottom Panel Replacement

Qué necesitas

  1. Xbox 360 Wireless Controller Bottom Panel Replacement, Battery: paso 1, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement, Battery: paso 1, imagen 2 de 2
    • Depress the battery release button on the top of the controller.

    • Remove the battery holder from the controller.

    • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

  2. Xbox 360 Wireless Controller Bottom Panel Replacement, Rear Case: paso 2, imagen 1 de 1
    • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

  3. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 3, imagen 1 de 1
    • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

    Any recommendation on which set of Security Torx tools to use? I've already purchased 2 kits, one of those being sold as "Xbox controller tools" but the diameter of the head does not fit the hole on the controller and that's critical for the 2 screws on the bottom. The tools must obviously be thinner in diameter and long enough to get there.

    Arnie - Contestar

    How to open an XBOX 360 controller without a special screwdriver. http://www.instructables.com/id/How-to-o... Works perfectly.

    Louis - Contestar

    A lot of thanks for your comment. It's very usefull

    Echedey -

    I picked up a handy torx key set from Auto Zone. Was about $10, no lose driver bits. has both sizes you need to repair the controller and the console. Here's the link:

    http://www.autozone.com/autozone/accesso...

    FierDancr - Contestar

    It doesn't really matter which set of bits you by or what brand makes them, Torx bits (and the security versions of them) are generic & come in standardized sizes. You do not need a special "xbox" tool kit, you just need a size 8 torx security bit, no matter what brand makes the bit/kit. Those types of "specialty kits" are usually just collections of generic bits that you can buy at a hardware store in a regular bit set. The difference is that a general bit set will have bits for screws that a specific item doesn't have in it, whereas a specialty kit will only include bits for the types & sizes of fasteners used in the specified item.

    BTW, with the smaller sizes of torx security bits you can try breaking off the little post in the middle with needlenose pliers or something else that can fit in the there. Even if the post doesn't break off cleanly, it's usually short enough to fit a regular (non security) torx bit in the slot.

    Nerfbomb - Contestar

  4. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 4, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 4, imagen 2 de 2
    Herramienta utilizada en este paso:
    Spudger
    $2.99
    Comprar
    • Insert a Spudger between the front and rear cases along the left edge of the controller.

    • Rotate the spudger toward the front of the controller, prying the two cases apart.

  5. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 5, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 5, imagen 2 de 2
    • Insert a spudger between the front and rear cases, near the headphone jack.

    • Rotate the spudger toward the front of the controller to pry the two cases apart.

  6. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 6, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 6, imagen 2 de 2
    • Grasp the controller by the battery compartment and the headphone jack.

    • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

    • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

    The RB / LB bar will fall away easily as you handle the upper case and logic board; just be prepared for it.

    knoxco - Contestar

  7. Xbox 360 Wireless Controller Bottom Panel Replacement, Vibration Motors: paso 7, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement, Vibration Motors: paso 7, imagen 2 de 2
    • Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.

    • Lift the vibration motor out of the front case.

  8. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 8, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 8, imagen 2 de 2
    • Remove the vibration motor from the other side of the controller using the same method previously described.

    • The left motor has significantly more counterweight than the right motor.

    The opposite was true for the controller I just opened. It was the left motor counterweight (as you hold the controller normally) which had more weight. Perhaps it doesn't matter which goes where?

    Bob S - Contestar

    For anyone reading this in the future, it does matter. The way you had them originally is the correct way.

    Yado Nada -

  9. Xbox 360 Wireless Controller Bottom Panel Replacement, Logic Board: paso 9, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement, Logic Board: paso 9, imagen 2 de 2
    • Lifting from the headphone jack and power plug, remove the logic board from the front case.

    What if you're having difficulty taking the logic board out?

    Xander Uchida - Contestar

    In my experience with my controller, the logic board lifts out very easily, there are no tabs or fasteners holding it in.

    So, if you're having difficulty taking the logic board out, call a friend with average hand dexterity & motor skills to do it for you.

    Nerfbomb - Contestar

    If the controller is a bit old, the center plastic screw holder might have swollen and will need a little stenght to release the logic board.

    RoFixedIt - Contestar

  10. Xbox 360 Wireless Controller Bottom Panel Replacement, Bottom Panel: paso 10, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement, Bottom Panel: paso 10, imagen 2 de 2
    • Lift the bumper panel off of the front case.

  11. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 11, imagen 1 de 1
    • Remove the rubber pad from the back of the D-pad.

  12. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 12, imagen 1 de 1
    • Remove the two 7.0 mm silver Phillips screws from the back of the D-pad.

  13. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 13, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 13, imagen 2 de 2
    • The D-pad is secured to its backing by two diagonal clips, shown in red.

    • Use a pair of tweezers and squeeze the clips together to release the D-pad from its backing.

  14. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 14, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 14, imagen 2 de 2
    • Lift the D-pad backing out of its compartment on the front case.

    • The D-pad remains below the front case.

    • The D-pad will fall once its backing is removed. Be sure to support it as you remove the backing.

    • The backing is slotted to its compartment to ensure that it will always be aligned properly.

  15. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 15, imagen 1 de 1
    • Remove the rubber pad from the back of the input buttons.

  16. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 16, imagen 1 de 2 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 16, imagen 2 de 2
    • Using a pair or tweezers, remove the following buttons from the front panel:

    • A Button

    • B Button

    • X Button

    • Y Button

    • Start Button

    • Select Button

    • Guide Button

  17. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 17, imagen 1 de 1
    • Using a pair of tweezers, remove the LED ring from the front panel.

  18. Xbox 360 Wireless Controller Bottom Panel Replacement: paso 18, imagen 1 de 3 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 18, imagen 2 de 3 Xbox 360 Wireless Controller Bottom Panel Replacement: paso 18, imagen 3 de 3
    • Insert a spudger between the lower panel and front case.

    • Slide the spudger along the gap between the two case components.

    • Lift the lower panel off of the front case.

Conclusión

To reassemble your device, follow these instructions in reverse order.

16 personas más completaron esta guía.

Brett Hartt

Miembro Desde 04/12/10

127,749 Reputación

143 Guías creadas

Equipo

iFixit Miembro de iFixit

Staff

136 Miembros

16,566 Guías creadas

Un comentario

I have 2 remote controllers of X box one which is not working.

ravi.gopalakrishnan - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 9

Ultimos 30 días: 66

Todo El Tiempo: 17,592