Introducción
Mejora tu puntería reemplazando las empuñaduras de palanca analógicas en el mando inalámbrico Xbox 360.
Qué necesitas
-
-
Presiona el botón de liberación en la parte trasera superior del control.
-
Extrae el portapilas del control.
-
-
-
Usa un par de pinzas para despegar la etiqueta del código de barras del compartimento de la batería.
-
-
-
Retira los siete tornillos Torx de seguridad T8 de 9,3 mm que sujetan la carcasa trasera a la carcasa delantera.
Any recommendation on which set of Security Torx tools to use? I've already purchased 2 kits, one of those being sold as "Xbox controller tools" but the diameter of the head does not fit the hole on the controller and that's critical for the 2 screws on the bottom. The tools must obviously be thinner in diameter and long enough to get there.
How to open an XBOX 360 controller without a special screwdriver. http://www.instructables.com/id/How-to-o... Works perfectly.
A lot of thanks for your comment. It's very usefull
Echedey -
I picked up a handy torx key set from Auto Zone. Was about $10, no lose driver bits. has both sizes you need to repair the controller and the console. Here's the link:
It doesn't really matter which set of bits you by or what brand makes them, Torx bits (and the security versions of them) are generic & come in standardized sizes. You do not need a special "xbox" tool kit, you just need a size 8 torx security bit, no matter what brand makes the bit/kit. Those types of "specialty kits" are usually just collections of generic bits that you can buy at a hardware store in a regular bit set. The difference is that a general bit set will have bits for screws that a specific item doesn't have in it, whereas a specialty kit will only include bits for the types & sizes of fasteners used in the specified item.
BTW, with the smaller sizes of torx security bits you can try breaking off the little post in the middle with needlenose pliers or something else that can fit in the there. Even if the post doesn't break off cleanly, it's usually short enough to fit a regular (non security) torx bit in the slot.
-
-
-
-
Sujeta el controlador por el compartimento de la batería y el conector para auriculares.
-
Levanta el compartimento de la batería para separarlo del conector de los auriculares, separando la carcasa trasera de la carcasa frontal y la placa lógica.
Good information
-
-
-
Usa el extremo plano de un spudger para quitar el cable del motor de vibración, moviéndolo hacia arriba desde su zócalo en la placa lógica.
-
Saca el motor de vibración de la carcasa delantera.
-
-
-
Retira el motor de vibración del otro lado del controlador utilizando el mismo método descrito anteriormente.
The opposite was true for the controller I just opened. It was the left motor counterweight (as you hold the controller normally) which had more weight. Perhaps it doesn't matter which goes where?
For anyone reading this in the future, it does matter. The way you had them originally is the correct way.
-
-
-
Levantando el conector de los auriculares y el enchufe de alimentación, extrae la placa lógica de la carcasa frontal.
What if you're having difficulty taking the logic board out?
-
-
-
Toma la palanca analógica derecha y saca la cubierta de su clavija de montaje.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
97 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
3 comentarios
unnecessary steps.
3 steps:
remove all 7 screws.
flip upside down remove top plate
pull stick caps off
reinstall in reverse.
you may have to slide the vibration motors into the slots on the top half when putting back together.