Introducción
Reemplaza un ventilador ruidoso, mugriento y golpeado para que tu Xbox 360 S suene como nueva.
Qué necesitas
-
-
En los siguientes pasos, removerás la ventila superior, asegurada al panel superior por los trece clips mostrados a continuación
-
-
-
Orienta la consola de modo que las palabras "XBOX 360" de los lados miren hacia la derecha y estén orientadas hacia arriba, y la placa frontal mire hacia la izquierda
-
Inserta un spudger metálico entre la ventila superior y el bisel superior cerca de la parte trasera de la Xbox
-
Rota el spudger hacia afuera de la consola, haciendo palanca hacia arriba en el borde de la ventila hasta que se liberen los clips de plástico
This step is and the others following are to rough and not needed, simply put smth in between the lamellar and push it up with littlebit pressure thats better for the plastic parts.
-
-
-
Inserta un spudger metálico entre la ventila y el bisel superior a lo largo del lado izquierdo de la consola
-
Del mismo modo descrito arriba, empieza a hacer palanca hacia afuera del bisel superior en el lado izquierdo de la ventila superior
-
Continúa haciendo palanca a lo largo del lado izquierdo del dispositivo, liberando todos los clips de ese lado
-
-
-
Inserta un spudger metálico a través de la ranura en el borde izquierdo del borde superior ubicada más al frente y entre el borde inferior del clip y la carcasa izquierda como se muestra arriba
-
Simultáneamente rota el spudger metálico hacia afuera de la consola tira hacia arriba en el bisel superior para liberar el clip
So I got the fan filter thing off, but the black edge plate thing isn't coming off. All I did was warp my flathead screwdriver and scratch the console.
-
-
-
Rota la consola de modo que la parte trasera de la Xbox 360 S mire hacia la derecha, y la carcasa derecha mire hacia ti
-
Inserta un spudger metálico a través de la ranura del borde derecho del bisel superior ubicada más hacia atrás, y entre el borde inferior del clip y la carcasa derecha
-
Rota el spudger hacia afuera de la consola mientras levantas el bisel superior con tus dedos para liberar el clip
-
-
-
Empuja hacia la izquierda el pestillo que sostiene la cubierta del disco duro
-
Tira la cubierta del disco duro hacia afuera de la consola
-
-
-
Agarra firmemente la etiqueta de tela que dice la capacidad del disco duro( Ej: 250 GB), unida al disco duro
-
Tira el disco duro hacia afuera de la consola
If i buy a new xbox 360 and replace the hardrive inside with my own, will i have my account and saves? or will i have to recover my account and start over?
You will still have your saves and account if you replace your hard drive in the new xbox
hola tengo un disco de laptop y quiero ponerle 100 juegos como puedo hacer la xbox me reconose el disco y todo lo configuro pero cuando conecto a mi pc para pasar los juejosel emulador no me deja
-
-
-
-
Inserta un spudger metálico a través de la abertura cerca la esquina inferior izquierda del bisel inferior
-
Rota el spudger hacia afuera del dispositivo mientras levantas el bisel inferior hacia arriba (valga la redundancia) con tu otra mano
These are pretty awkward to remove, but once you understand how they work its easy enough. The goal here is to slot the spudger THROUGH the gap of the silver tabs (visible in previous steps image, circled) and then pry. Put pressure against the wall of the Xbox case and push downwards, once you feel the spudger slot in, then apply force away from the Xbox and pull up a little with your free hand.
-
-
-
Inserta un spudger metálico a través de la abertura izquierda en medio del bisel inferior, y entre el borde inferior del clip y la carcasa izquierda
-
Jala hacia arriba el bisel inferior y rota el spudger hacia afuera de la consola simultáneamente para liberar el clip
-
Libera el clip al frente del borde izquierdo del bisel inferior del mismo modo
-
-
-
-
Localiza los dos clips que conectan el panel izquierdo y el derecho junto al borde de la parte de arriba de la consola, detrás de la carta del Wi-Fi.
-
Mientras empujas el panel izquierdo y el derecho lejos de cada uno con una mano, saca los clips del panel con una espátula de metal.
-
-
-
Inserta el borde plano de un spudger de metal entre las cajas izquierda y derecha donde solía estar la etiqueta de garantía.
-
Haz palanca en la caja izquierda hacia arriba para formar un espacio entre las dos cajas y desliza el spudger hacia la caja izquierda.
-
Gira el spudger hacia arriba para liberar el último clip.
if you make a hole right here like the link`s picture you can boot the lock
As the user above me said, please avoid doing it like shown in the guide. It just didn’t work on my Xbox (unless your goal is to destroy the plastic case). Instead, pick some small needle like object (the spudger was too short for this, I used the SIM bit of my iFixit driver kit) and find the right spot on the big sticker which is on the left in the pictures shown in the guide. That spot is just between the text and the column of logos (Dolby Digital, etc.) (https://team-xecuter.com/slim/slim_secre..., picture not mine). Poke it (don’t be too gentle, you have to apply some force) and you will hear the clip release.
Both the above links are dead, i used this YouTube video which shows you the process of getting the hidden clip
I was able to open it by pushing on the sticker to unclamp the clip while another person helped me pull open the case.
Here is a Video that shows the small hole behind the sticker, ist in german but ist good to see how to open that hidden clip easiely.
-
-
-
Voltea la consola de modo que la parte inferior quede hacia arriba.
-
Suelta un clip en la esquina frontal izquierda del borde inferior que sujeta la carcasa izquierda a la placa frontal.
-
Gira la carcasa izquierda lejos del dispositivo para liberar los dos últimos clips internos.
-
Retira la carcasa izquierda.
-
-
-
Suelta el clip cerca de la esquina frontal derecha del borde superior que sujeta la carcasa derecha a la placa frontal.
There are 4 black screw that has to be removed before you can detach the other cover. Please note
Sorry, there 5screws, one in the middle and 4 at the edges
-
-
-
Levanta el borde izquierdo de la placa frontal hacia arriba para soltar los dos últimos clips que sujetan la placa frontal a la caja derecha.
-
Separa la placa frontal del resto del dispositivo.
There isn’t 2 clips there is 4 clips
-
-
-
Usando un spudger o una uña, levanta la pestaña azul transparente del conector.
-
Desliza la lengüeta de bloqueo del conector del cable de la placa del interruptor de alimentación hacia la parte superior de la consola.
-
Saca el cable del interruptor de alimentación directamente del conector.
-
La placa frontal ahora está libre del resto de la consola.
-
-
-
Retira los dos tornillos Torx T8 de 5,6 mm que sujetan el módulo de RF a la caja de metal.
On my disassembly during this part, I found the T9 Torx to be too big and had to use the T8 Torx instead.
The correct size is T8!
-
-
-
Tira de la placa directamente lejos de la Xbox para quitarla.
It may not be required but recommended. As you move the xbox around you could break this part. Removing it and placing it in a safe place keeps that from happening.
-
-
-
Retira el único tornillo Torx T10 que sujeta la tarjeta inalámbrica.
-
Extrae la placa Wi-Fi de la consola.
-
-
-
Retira la etiqueta de garantía blanca grande del marco de metal para exponer un tornillo.
-
-
-
Desconecta el cable de datos de la unidad óptica de la parte posterior de la unidad óptica.
-
Desconecta el cable de alimentación de la parte posterior de la unidad óptica.
-
-
-
Levanta la unidad óptica de la Xbox.
Is there a specific Optical Drive that Microsoft uses in these or can I upgrade my drive?
i took my drive out but when installed my replacement it would not work
WAS thinking of possibly trying to repair my son's Xbox 360S, by replacing the optical drive, but after looking at all the spudger steps to get to the drive and then your comment that the replacement might not actually work... forget about it! I ain't going to all that work for possibly nothing... t'ain't worth it!
Anyone want a perfectly working Xbox 360S with a drive the spins game discs upon ejection? We've already bought a replacement, so this unit is for sale... name your price.
Luposian -
In regards to davidgardner301 comment there is a extra step they. Didn't show on this replacement guide in order for your new disk drive to work you will need to remove the origional board connected to thje origional drive that came with the system and soler that onto the new one its a tricky process however its a step most people over look
Without the origional board the xbox will not accept the replacement drive only because each disk drive is coded to work with tat soecific xbox only so your out of luck if you already. Tossed out your old disk drive
The DVD drives are coded to the Motherboard. If you buy the same exact drive to replace the broken one. You will still need to either 1) transfer the DVD circuit board OR 2) get the Firmware from the old DVD drive using a PC and then transfer it to the New DVD. There are website regarding this procedure if you want to look it up.
-
-
-
Retira el único tornillo Torx T10 dorado de 11,3 mm del orificio marcado con "G".
-
-
-
Levanta el soporte del disco duro para sacarlo del marco de metal.
I have a 4GB Xbox 360 slim and I bought a 500GB hard drive for it. I pushed the hard drive in its place and after I heard that click, I pushed it a little bit more to be shure that it's in place. I noticed that the hard drive bracket (the slide that holds the hard drive) it's elastic: after the hard drive is inserted, it wobbles (maybe to prevent hdd damage when the xbox is moved).
My question is: how does the hard drive bracket work? is there a metal spring in its mechanism that allows it to wobble? Did I make any damage to it because I pushed the hard drive to be sure that it is in place? I don't want to teardwon my console to find that out.
Thank you!
-
-
-
Desconecta el cable del ventilador tirando de su conector de la placa lógica.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
101 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
7 comentarios
Do I need to buy a new fan, or does this tutorial basically use a method of cleaning things out to fix the fan?
A bit late I know, but if you’re getting this deep into the system, put in a new fan.
This tutorial was perfect.
Thank you Mr. Newsom!
what wrong with x360 s
So could I water cool this thing?
You probably could if you can get the waterblock to fit into the xbox. but the radiator and fans might be tricky unless you just have those outside the case.
i just used this guide to clean out my 2010 360s, RIP 360 marketplace