Recambio de la funda exterior del Wii U GamePad

Introducción

Esta guía te ayudará a quitar la carcasa exterior y poder abrir el Nintendo Wii U Gamepad. Necesitarás un destornillador Tri-WIng Y1.

Qué necesitas

Paso 1 Batería

Recambio de la funda exterior del Wii U GamePad, Batería: paso 1, imagen 1 de 1

Coloca el Gamepad boca abajo y retira los dos tornillos de 4,7 mm con un destornillador Phillips de tamaño #00.

Traducir

tried to unscrew the 10 Tri-Wing size Y1 screw with my iFixIt toolkit

unfortunately the tool is too “fat” and short, it cannot reach 4 screws on the corners of the gamepad.

having the iFixIt toolkit and needing to purchase an additional slim screwdriver it’s a shame…

Antonello Iannone - 7 de mar. de 2021 Contestar

Paso 2

Levanta y retira la placa de la batería.

Traducir

Paso 3

Recambio de la funda exterior del Wii U GamePad: paso 3, imagen 3 de 3

Con el dedo, presiona hacia abajo y tira hacia atrás de la clavija del conector de la batería.
Extrae la batería de su estuche.

Traducir

Battery lifts up from the bottom not the top like the photo shows.

Tyler Schommer - 5 de oct. de 2017 Contestar

Paso 4 Caja exterior

Recambio de la funda exterior del Wii U GamePad, Caja exterior: paso 4, imagen 1 de 3

Recambio de la funda exterior del Wii U GamePad, Caja exterior: paso 4, imagen 2 de 3

Recambio de la funda exterior del Wii U GamePad, Caja exterior: paso 4, imagen 3 de 3

Retira 10 tornillos de 9 mm con un destornillador Tri-Wing tamaño Y1 alrededor de la carcasa exterior.
Levanta la parte posterior de la caja.
Levántalo con cuidado porque el motor de rumorosidad de la parte posterior de la carcasa sigue conectado por un cable a la placa base.

Traducir

I used a small blade tip to life up on the black squares that covered the screw holes. Replacing them after.. I skipped that as it seemed impossible they would even stick back down.

Chris - 29 de oct. de 2018 Contestar

I am having trouble getting the two screws on the hand grips as the screws are too deep. What should I use to get them?

[deleted] - 10 de jun. de 2021 Contestar

I ended up having to buy some cheap amazon screwdrivers and are very disappointed

[deleted] - 10 de jun. de 2021

Paso 5

Desenchufa con los dedos el conector exterior del motor de resonancia de la placa base.

Traducir

Do not pull by the wires! If you do, you better be pretty good at soldering.

Brandon - 9 de abr. de 2018 Contestar

I agree. A circle over the plug would have been better as the picture looks like you just pull on the wires lol.

Chris - 29 de oct. de 2018

Thanks for the comment. I did get a set of tweezers and the negative cable broke anyway. They really could have done a better job at using a different connector for that.

Kristen Bartholomew - 20 de nov. de 2021

Great. Didn't pull on cord. Whole thing ripped off.

August - 6 de may. de 2020 Contestar

Why in the world is this thing so tightly connected?

Andrew Moore - 9 de nov. de 2020 Contestar

Thanks for the comment. I did get a set of tweezers to try to pull it out but still ended up breaking the negative cable. They really could have used a better set of cables and connectors for this.

Kristen Bartholomew - 20 de nov. de 2021 Contestar