Saltar al contenido principal

Reparación de la rueda de desplazamiento del ratón VicTsing

Qué necesitas

  1. Reparación de la rueda de desplazamiento del ratón VicTsing, Reparación de la rueda de desplazamiento del ratón VicTsing: paso 1, imagen 1 de 1
    • Retire la tapa de la batería y la batería del compartimento. Luego use el spudger de metal para retirar las almoadillas.

  2. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 2, imagen 1 de 1
    • Use un destornillador Phillips # 000 para retirar los 3 tornillos.

  3. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 3, imagen 1 de 2 Reparación de la rueda de desplazamiento del ratón VicTsing: paso 3, imagen 2 de 2
    • Con cuidado, separe la base y la carcasa superior una de la otra.

  4. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 4, imagen 1 de 1
    • Retire los dos puertos de cable conectados para poder separar la carcasa superior de la base.

    • Esto puede requerir un poco de esfuerzo, use el spudger si es necesario.

  5. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 5, imagen 1 de 1
    • Retire la placa de circuito de la base de plástico del ratón.

  6. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 6, imagen 1 de 1
    • Aleje la rueda del codificador rotatorio y levántela para extraerla.

  7. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 7, imagen 1 de 2 Reparación de la rueda de desplazamiento del ratón VicTsing: paso 7, imagen 2 de 2
    • Utilice pinzas para apretar el codificador rotatorio. Haga esto en múltiples lugares.

    • No aplique demasiada presión al codificador rotatorio o se romperá.

  8. Reparación de la rueda de desplazamiento del ratón VicTsing: paso 8, imagen 1 de 1
    • Limpie cualquier polvo o suciedad que vea en la carcasa.

Conclusión

Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.

16 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ Carlos Rafael Ramirez nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

16 comentarios

Very detailed repair guide!!!

Austin Melton - Contestar

THANK YOU! Saved me from spending another $10 on a mouse after 6 months. Those screws under the adhesives are pretty hidden…

Michael Shingo Crawford - Contestar

Thanks! I was thinking to buy another but it is fixed! It works on the model VicTsing CA32-es2 too, that’s mine.

Antonio Ruiz - Contestar

Excellent guide, thanks! I have a Victsing PC134A vertical mouse. The assembly is different, so I ended up removing about 12 screws, only to then realize that I could easily access the “rotary encoder” part with zero screw removal. :) For Victsing PC134A, just pop off the the left-right click cover, and tweeze as suggested in this guide. It worked!

Thanh - Contestar

That’s crazy! Why does squeezing the rotary encoder fix it? Thank you so much for the guide!

Ben Sutton - Contestar

I have the same question, please someone

Carlos Rafael Ramirez -

Awesome… managed to repair BOTH of my VicTsing MM057 wireless mice with that issue (less than 6 months old). Bought the second to replace one that had failed, thinking it was a matter of bad luck, and that erratic-scrolling issue appeared even earlier than in the first one. In less than half an hour I put both to work again… Really appreciate your help!

Regards from South America.

Marcelo Soto-Quiroga - Contestar

Thanks much. It worked.

Sumit Chowdhury - Contestar

Hello,

It worked, but after some time it broke again. Do anyone have a more permanent solution for it?

Regards,

Carlos

Carlos Rafael Ramirez - Contestar

This fixed my issue. Thanks

Joey Wong - Contestar

This is very helpful. I appreciate it. One thing i ask is if you make a guide to fixing a Mouse scroll wheel on a VicTsing PC140A wireless mouse. That would be a great help.

Albert Einstin - Contestar

I have a Victsing corded mouse, PC081A. I got no results from squeezing the encoder, but that led me to discover that the shaft of the wheel needs to apply axial pressure on the encoder (leftwards with the mouse in normal position). My mouse has two plastic “towers” molded in the plastic of the base, with a slot in each where the shaft rides. I cut a small wooden wedge from a coffee stirrer, about 3 x 8 mm, and inserted it between the right tower and the microswitch to its right, which is the wheel button switch, This pushed the right tower leftwards, and forced the shaft towards the encoder. That restored the scroll function.

R bye - Contestar

Hello, thanks for the tutorial. My mouse is the same as this model.

From time to time it simply disconnects by itself and after a few seconds, it reconnects. I’ve changed batteries already.

This one problem is very annoying, but it works perfectly and I’d really like to keep using it - so I wish I could fix it to continue using it.

Do you guys know anything I could do to solve this?

Victor Pietro Moreno - Contestar

Worked well fixing the d-09 mouse (of many names on amazon) aka hotweems and probably others.

Angelo C - Contestar

The encoder is a very simple device where a tiny round metal plate contacts another piece of metal to detect the rotation. However, over time, the contact surface becomes dirty. By squeezing the device, the contact will be a little tighter, thus result in better conduction. But this won't be a permanent fix since the dirt and grease will get in-between eventually. An alternative fix can be simply spray some WD-40 or other electronic cleaner there.

grace wu - Contestar

A more permanent fix would be to disassemble it and thoroughly clean up the tiny metal plate inside. That will make it just like new one.

grace wu - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 5

Ultimos 30 días: 19

Todo El Tiempo: 7,831