Introducción

If you find that your disc isn't reading despite no scratches, use this guide to remove and replace the optical lens.

  1. Remove the three 6mm Phillips head screws on the back of the DVD player with a Phillips #1 screwdriver.
    • Remove the three 6mm Phillips head screws on the back of the DVD player with a Phillips #1 screwdriver.

  2. Remove the two 3mm Phillips screws on each side of the DVD player using the Phillips #1 screwdriver. Remove the two 3mm Phillips screws on each side of the DVD player using the Phillips #1 screwdriver.
    • Remove the two 3mm Phillips screws on each side of the DVD player using the Phillips #1 screwdriver.

  3. Using your hand, gently lift the black top panel and safely place it off to the side.
    • Using your hand, gently lift the black top panel and safely place it off to the side.

  4. Remove five 6mm Phillips screws with a Phillips #2 screwdriver. The 2 screws on the right of the cartridge are better shown in the second and third photos. The 2 screws on the right of the cartridge are better shown in the second and third photos.
    • Remove five 6mm Phillips screws with a Phillips #2 screwdriver.

    • The 2 screws on the right of the cartridge are better shown in the second and third photos.

  5. Remove the remaining four 6mm Phillips screws. Remove the remaining four 6mm Phillips screws.
    • Remove the remaining four 6mm Phillips screws.

  6. ¡Envío gratuito para todos los pedidos de más de USD100 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda
  7. Using your fingers, gently remove the metal pieces on each side of the cartridge and carefully place them aside. Using your fingers, gently remove the metal pieces on each side of the cartridge and carefully place them aside. Using your fingers, gently remove the metal pieces on each side of the cartridge and carefully place them aside.
    • Using your fingers, gently remove the metal pieces on each side of the cartridge and carefully place them aside.

  8. Gently lift the cartridge. Remove two 4mm Phillips screws from the green circuit board. Gently lift the cartridge. Remove two 4mm Phillips screws from the green circuit board.
    • Gently lift the cartridge. Remove two 4mm Phillips screws from the green circuit board.

  9. Using your fingers, gently pull off the wires.
    • Using your fingers, gently pull off the wires.

  10. Using your fingers, pull off the green circuit board from the cartridge and carefully place it down. Be careful not to rip the tape attaching the green circuit boards together.
    • Using your fingers, pull off the green circuit board from the cartridge and carefully place it down.

    • Be careful not to rip the tape attaching the green circuit boards together.

  11. Flip the cartridge over to the bare side with no stickers. Remove four 10mm Phillips screws from each corner. Flip the cartridge over to the bare side with no stickers. Remove four 10mm Phillips screws from each corner.
    • Flip the cartridge over to the bare side with no stickers. Remove four 10mm Phillips screws from each corner.

  12. Using your hands, gently lift the lid and carefully place it aside. Using your hands, gently lift the lid and carefully place it aside.
    • Using your hands, gently lift the lid and carefully place it aside.

  13. Flip over the cartridge. Using your hands, gently lift the rest of the silver case. Flip over the cartridge. Using your hands, gently lift the rest of the silver case. Flip over the cartridge. Using your hands, gently lift the rest of the silver case.
    • Flip over the cartridge. Using your hands, gently lift the rest of the silver case.

  14. The optical lens will be resting aside the small green circuit board.
    • The optical lens will be resting aside the small green circuit board.

  15. Using a prying tool, wedge the edge of the tool underneath the end of the optical lens closest to the green circuit board. Gently push down to pop off the optical lens. Using a prying tool, wedge the edge of the tool underneath the end of the optical lens closest to the green circuit board. Gently push down to pop off the optical lens.
    • Using a prying tool, wedge the edge of the tool underneath the end of the optical lens closest to the green circuit board. Gently push down to pop off the optical lens.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Nouriyah Saleh

Miembro Desde 22/10/18

749 Reputación

6 Guías creadas

Equipo

UC Davis, Team S11-G1, Lore Fall 2018 Miembro de UC Davis, Team S11-G1, Lore Fall 2018

UCD-LORE-F18S11G1

3 Miembros

6 Guías creadas

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 5

Todo El Tiempo: 28