Repara tus cosas Comunidad Tienda

SwagTron T1 Gyroscope Replacement

Introducción

This guide will show you how to replace the gyroscope component of your SwagTron T1. This may be necessary if the self-balancing function of your hoverboard is not working correctly. Before attempting this replacement, recalibrate your SwagTron. If the problem persists, continue with this replacement. This replacement can be done for the gyroscope component on either side of your SwagTron T1.

Qué necesitas

  1. SwagTron T1 Gyroscope Replacement, Back Panels: paso 1, imagen 1 de 1

    • Ensure that the SwagTron is off.

    • Turn the SwagTron upside down to see the underside.

    Editar

  2. SwagTron T1 Gyroscope Replacement: paso 2, imagen 1 de 3 SwagTron T1 Gyroscope Replacement: paso 2, imagen 2 de 3 SwagTron T1 Gyroscope Replacement: paso 2, imagen 3 de 3

    • Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver.

    • The screws are tightly in place. It will take effort to screw them out.

    • The panel is still attached to the SwagTron by wires that go to the motherboard.

    • Carefully lift the panels off

    Editar

  4. SwagTron T1 Gyroscope Replacement: paso 3, imagen 1 de 3 SwagTron T1 Gyroscope Replacement: paso 3, imagen 2 de 3 SwagTron T1 Gyroscope Replacement: paso 3, imagen 3 de 3

    • Follow the wires from the panels to the motherboard.

    • You may need to cut any zip ties that are holding the wires together.

    • There is one connection on the battery side and three on the other side that must be removed.

    • These connections may be difficult to remove. Try to securely press the connection and pull firmly.

    • Your back panels are now completely removed.

    Editar

  5. SwagTron T1 Gyroscope Replacement, Gyroscope: paso 4, imagen 1 de 2 SwagTron T1 Gyroscope Replacement, Gyroscope: paso 4, imagen 2 de 2

    • Disconnect the gyroscope by disconnecting the wires attached to it. These wires are black, green, blue and red.

    Editar

  6. SwagTron T1 Gyroscope Replacement: paso 5, imagen 1 de 1

    • Using your Phillips #2 screwdriver, remove the four 8mm screws marked in red from the gyroscope.

    Editar

  7. SwagTron T1 Gyroscope Replacement: paso 6, imagen 1 de 3 SwagTron T1 Gyroscope Replacement: paso 6, imagen 2 de 3 SwagTron T1 Gyroscope Replacement: paso 6, imagen 3 de 3

    • Carefully remove the gyroscope component from the SwagTron.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

9 personas más completaron esta guía.

Autor

con 3 otros colaboradores

Teagan Allen

Miembro Desde 04/18/17

426 Reputación

2 Guías creadas

Insignias: 10

+ 7 más insignias

Equipo

Cal Poly, Team S17-G5, Banghart Spring 2017 Miembro de Cal Poly, Team S17-G5, Banghart Spring 2017

CPSU-BANGHART-S17S17G5

4 Miembros

5 Guías creadas

5 comentarios

I cannot find a Swagtron T1 replacement gyroscope anywhere on the internet. Any help would be extremely appreciated!! Thank you!

Gavin Hosler - Contestar

Amazon.com Keyword: CertiCable

Jesse Griffis -

Where do you get the replacement?

Brittany Conner - Contestar

Can’t find gyroscope for a t5 hover board please help.

jbswearingen70739 - Contestar

I just got mine today and after the first hour I ran into a shoe and then I tried recalibrating it but it was no use. If someone knows what’s going on please tell me! Thank you :)

Elia Leon - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 9

Ultimos 30 días: 39

Todo El Tiempo: 7,215