Introducción
Sustituye el ventilador de tu PlayStation 2.
Qué necesitas
-
-
Utiliza la parte plana de una espátula metálica para hacer palanca y quitar las patas de goma que ocultan los tornillos.
-
Quita los siguientes ocho tornillos que aseguran la carcasa superior con la inferior.
-
Cuatro tornillos Phillips de 55.4 mm.
-
Cuatro tornillos Phillips de 18.0 mm.
-
-
-
Algunos modelos tienen un número diferentes de tornillos y patas de goma. Quita todos los que veas en la carcasa inferior.
-
El modelo que tiene 10 tornillos, tiene 6 en la parte inferior y 4 en la bandeja superior de la parte inferior. Échale un vistazo a la foto para que te quede más claro.
-
-
-
Levanta la carcasa superior de la carcasa inferior.
-
Con cuidado quita el cable de alimentación que une ambas mitades, para ello desconéctalo de la parte inferior de la carcasa.
If you have a 5000x model, then the power and reset buttons are attached to the console, not the lid. Therefore there won’t be a cord
-
-
-
Quita los 2 tornillos Phillips de 6.4 mm de color negro que están asegurando la unidad de disco a la parte inferior de la carcasa.
-
Levanta y quita la unidad óptica de la parte inferior de la carcasa.
-
-
-
-
Con suavidad levanta la tarjeta de alimentación de su hueco dentro de la carcasa inferior.
-
Tira del cable plano de las ranuras de los mandos para así sacarlo de su zócalo.
-
Quita las ranuras para los mandos de la carcasa inferior.
El conector del flex del modulo de conectores de los mando y las memory card no va a presión, para volver a colocarlo, hay que abrirlo.
Controller is detached can we fix it?
The clip which holds the controller is broken
-
-
-
Haz palanca y quita la tapa de la bahía de expansión de su hueco en la carcasa inferior.
If there is a harddrive in the system place switch on off position before removing and reinstalling because it may blow the fuse that runs the harddrive!
-
-
-
Quita los cuatro tornillos Phillips de color dorado de 7.6 mm que aseguran la fuente de alimentación al conjunto de la placa base.
If you have a 5000x model, then the power supply will be flipped upside down (or right side up). the screws are in the same positions
-
-
-
Quita el protector plástico contra el calor del montaje de la placa base.
-
-
-
Quita la pequeña pieza de cinta blanca (marcada en en la foto con un cuadro rojo) que mantiene el cable del ventilador conectado al ventilador.
-
Tira del cable del ventilador hacia arriba para quitarlo de su zócalo en la placa base.
-
Quita el ventilador y el botón tirando de ellos y quitándolos de la placa base.
-
-
-
Quita el botón de encender de su hueco en el ventilador/botón de encendido de su hueco.
Can someone tell me how to hook my fan back to my p2 the connector got snatched out
-
Para volver a montar tu PlayStation 2 sigue las instrucciones en orden inverso, desde el final hacia el principio.
Para volver a montar tu PlayStation 2 sigue las instrucciones en orden inverso, desde el final hacia el principio.
Cancelar: No complete esta guía.
37 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ MemoryOverflow nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
10 comentarios
what about on fixing when the unit doesn't turn back on? Replaced the ribbon cable after blowing out the dust, reassemble the unit and it didn't turn back on no green or red light's.
You should check to c if the side with the blue is on the top @ the silver on the bottom
What about the slim model? Is there a guide for that?
I have a question about this I just want to clean off the fan not replace it how do I do
A nice ol' bottle of compressed air will do the trick. You have two options, either open the console up and give it a spurt from the inside, or be lazy like me and shoot it from the outside! Cheers!
When you’ve gotten to the fan, instead of unplugging and removing the fan, clean it with cotton swaps dipped in isopropyl alcohol that is 90% or higher.
I tried replacing the fan with a new one but it still doesn’t spin, I guess the fuse popped for some reason so I just got a usb fan and drilled holes at the top of my console and stuck the fan there with cable ties
did you ever fix your fan?
الزر الاحمر لا يعمل مع انة متصل بالكهرباء
Before proceeding to step 2, Take a look at your PS2, some PS2's have 10 screws (and screw covers) instead of 8 (i found them underneath the optical drive), these instructions have mislead me and i ended up breaking my top cover for my PS2.
Tristan - Contestar
Ich möchte daraufhin weisen, daß es bei der SCPH-50004 zwei verschiedene Schraubabdeckungen gibt.
4x Kreuzförmig 4x rechteckig
Sowie eine silberne schraube die sich an der unterseite aufhöhe des Reset-Knopfes befindet.
Christian Lehnhardt - Contestar