Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Introducción

Utiliza esta guía para sustituir una placa de control rota.

  1. Utiliza la punta de una espátula para quitar la pata de goma negra que esconde un tornillo, esta se encuentras en el lado de tu PS3. La pata de goma puede estar debajo de una pegatina de garantía. Si la despegas, esta mostrará "VOID" después de quitarla. (Lo que anulará la garantía).
    • Utiliza la punta de una espátula para quitar la pata de goma negra que esconde un tornillo, esta se encuentras en el lado de tu PS3.

    • La pata de goma puede estar debajo de una pegatina de garantía. Si la despegas, esta mostrará "VOID" después de quitarla. (Lo que anulará la garantía).

  2. Quita el tornillo de 8.5mm T10 Tor de seguridad de la smart plate.
    • Quita el tornillo de 8.5mm T10 Tor de seguridad de la smart plate.

  3. Tira de la smart plate hacia la bahía del disco duro, después levántala del cuerpo de la PS3. Tira de la smart plate hacia la bahía del disco duro, después levántala del cuerpo de la PS3. Tira de la smart plate hacia la bahía del disco duro, después levántala del cuerpo de la PS3.
    • Tira de la smart plate hacia la bahía del disco duro, después levántala del cuerpo de la PS3.

  4. Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

    Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch
  5. Asegúrate de no perder de vista el raíl metálico en caso de que esté equipado en la carcasa superior.
    • Asegúrate de no perder de vista el raíl metálico en caso de que esté equipado en la carcasa superior.

    That small metal bracket/socket set up looks completely different in the ps3 I'm working on. Model: CECHK01.

    Any suggestions?

    Marcus - Contestar

    different in mine too, Model: CECHP01

    Link Adrian - Contestar

  6. Quita los siete tornillos siguientes:
    • Quita los siete tornillos siguientes:

    • Seix tornillos Phillips de 52mm.

    • Un tornillo Phillips de 30mm.

    2 more smaller screws (don't know what size...small) just below the top middle screw and top right screw (in the picture). Look for the arrows...

    E Goo - Contestar

    after you remove the screws, you may have to push a tab to take the cover off if you meet resistance on one side of the cover. Here is a link to a video that explains it, saved me lots of trouble:

    http://youtu.be/jZgekNsRB-A?t=1m54s

    ericksi33 - Contestar

    Thanks @ericksi33, this really helped me out.

    hogurt -

    1st attempt, fan loud. Ps3 lasted about 2 wks. 2nd attempt noticed very poor contact between heatsink & cpu,gpu when taking it apart. Research - Found a better way to apply thermal past. I personally disapprove of guide on this. A small bit about the size of a grain of rice in center of cpu is plenty. Clamp the heat sinks back on. Then take it apart & check contact area. Thermal paste should have spread to about the size of a quarter.(more is better. Less then a nickel size is poor contact) possibly weak clamps. Carefully applied pressure onto the cpu & gpu, pressing them into the heatsinks before clamping heatsink clamps on. Achieved greater then quarter sized thermal past spread. Fan silent in comparison & ps3 lasted about a yr. Rarely did I ever hear the fan go to high and get loud after that. About to begin my third fix on this same ps3. One of the first 80g backwards compatible. other then those notes and that this guide was for a different model ps3 (minor differences) I liked this guide. easy to follow.

    brettgomes - Contestar

    Although the battery is described as proprietary, it looks like it is the common CR2032 lithium coin battery that is used in calculators and some computers. I haven't had to replace mine but I suspect under the heatshrink cover is a battery holder which will allow the coin battery to be removed and replaced. Then wrap with electrical tape and reinstall.

    RickP - Contestar

    I tried this with the heatgun and it ruined my PS3. The CPU and GPU are NOW RUINED!!! It did not work for and made things worst!!! I sent it to a place to get reballed and they said the HEATGUN had overheated my processor and killed them!!! So think twice about doing this. Just because it is already broken, DON'T THINK YOU CAN'T MAKE IT WORST!

    georgehollyoh - Contestar

    Why would you try it with a heat gun, no were is it mentioned to do that

    Phillip Pereira -

    There are 2 additional screws to remove , front center and front left , just behind the already marked screws.

    mikentc90 - Contestar

    As mentioned and I’ll add so detail too. If you have a model with the card readers there are two more small screws that also need to be removed before moving on to the next step.

    screech - Contestar

  7. Levanta la carcasa superior desde su borde trasero y rótala hacia la parte frontal de la PS3.
    • Levanta la carcasa superior desde su borde trasero y rótala hacia la parte frontal de la PS3.

    • Quita la cubierta superior.

    • Hay un gancho de plástico ubicado en un orificio en la esquina superior derecha posterior. Empuja con cuidado el gancho de plástico un poco por delante de la parte posterior de la PS3 con una espátula para soltar la parte posterior derecha de la carcasa.

    Disconnect the memory card ribbon cable.

    Tobias Stockmann - Contestar

    The top would hardly budge on the left back corner and was stuck on the right back corner. There is a plastic hook that needs to be unfastened to lift the top off. It is located in a hole on the top back corner on the right hand side, so the corner straight across the on off button. Just gently push the plastic hook a bit front the rear of the machine with a spudger. It gives easily and the top will be free to lift off after that.

    cornellg - Contestar

    Some more details here as well.

    The newer model without SACD support appears to have added that clip to the back right that needs to be pressed to release the top shell.

    If equipped with the card reader you can either have to disconnect the ribbon cable or unclip the reader from the top shell after lifting it up to get finger or tool in there to push clip to side and release reader from top shell. Note: if you failed to remove the card reader screws in the previous step these clips can break.

    screech - Contestar

  8. Utiliza tus uñas para levantar la pestaña que sujeta el cable plano. Asegúrate de que estás haciendo palanca en la pestaña y no en el zócalo en sí.
    • Utiliza tus uñas para levantar la pestaña que sujeta el cable plano.

    • Asegúrate de que estás haciendo palanca en la pestaña y no en el zócalo en sí.

    • Tira del cable de la placa de control fuera de su zócalo.

  9. Quita los dos tornillos Phillips de 12 mm que sujetan la placa de control a la carcasa inferior.
    • Quita los dos tornillos Phillips de 12 mm que sujetan la placa de control a la carcasa inferior.

  10. Quita la placa de control de la carcasa inferior.
    • Quita la placa de control de la carcasa inferior.

Conclusión

Para volver a ensamblar tu dispositivo, sigue los pasos de arriba en orden inverso.

12 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

I don't have the same ps3 as in the tutorial and my control board is broken. What can i do now?

McGarvey - Contestar

Could anyone tell me if they would have the connection pin of this board, as I would like to fit it into a motherboard.

Allan Fabian Santos Souza - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 7

Ultimos 7 días: 36

Ultimos 30 días: 148

Todo El Tiempo: 44,034