Introducción
Si necesitas cambiar la fuente de alimentación de tu consola, significa que ésta no recibe suficiente potencia y por ese motivo no funciona correctamente.
Antes de empezar esta guía asegúrate de tener las herramientas adecuadas (listadas abajo), bastante tiempo libre y un espacio limpio y ordenado para trabajar.
Cuando sigas los pasos de esta guía, sé cuidadoso cuando apliques presión en diferentes partes y componentes que se puedan doblar o romper fácilmente.
Igualmente, ¡tómate tu tiempo y asegúrate de leer los pasos con atención mientras trabajas en la sustitución de la fuente de alimentación!
Qué necesitas
-
-
Quita la cubierta que cubre la bahía del disco duro deslizando el panel desde atrás hacia delante de la consola.
-
-
-
-
En la parte superior de la consola, desengancha el gancho que se encuentra en el extremo derecho debajo del panel frontal, levanta ligeramente el panel y aplica presión.
-
Desenganche el segundo gancho del lado derecho deslizando la herramienta de plástico en el área marcada.
-
Desliza el panel a la izquierda para desenganchar el resto de los ganchos.
-
-
-
Mueve la unidad óptica para un lado y descubre uno de los tornillos largos plateados de 8.8mm.
-
Quita los tornillos largos plateados de 8.8mm de cada lado con un destornillador Phillips #1.
be careful, the fiber-optic cables come out easily and are a pain to put back in
-
-
-
Quita el cable del enchufe y quita los cables de los dos ganchos de plástico.
-
Quita la fuente de alimentación.
The left side of the PSU sits on two long metal prongs so you may need to pull a little to get it lose but you should be able to pull the whole unit in an upward motion
-
Instala el recambio de la fuente de alimentación. Para volver a montar la consola ,sigue las instrucciones en el orden contrario.
Instala el recambio de la fuente de alimentación. Para volver a montar la consola ,sigue las instrucciones en el orden contrario.
Cancelar: No complete esta guía.
22 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ BufferUnderflow nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
8 comentarios
Perfect how to guide. Fixed my PS3 easily. Thanks
Great guide. However, still no power on PS3. Any suggestions as to what else may be the problem?
Peter Maher, I am in the same boat. I have no idea what the problem is. Red light in standby, but as soon as I try to power on, nothing. Same as before I did this power supply replacement. Obviously, something else is the problem. Anyone who has some insight into this please help!
Did you guys get word on the red light with no power on fix mine has the same issue.
i have the same problem as Peter Maher, the red light is in standby neither turning green on pressing nor it sounds beep on long press. dont know whats wrong. anyone has any solution to this?
thanks for guide - had a blown power unit and this was a useful guide to getting at it so it could be replaced. I couldn’t see a guide for taking the power unit apart so with nothing to lose I opened that up to see what was going on, and could see the charred remains of what I guess was a capacitor. New power unit in there now and working great. thanks
Fantastic guide, I used it today to check if my PS3 brought from the US could be plugged in a 220 socket (as I had read on this site). I can confirm this is the case, as the power supply is actually the 100-240V one (part # N12-160P1A). Thanks for this great piece of information!
Just wanted to add: the HDD bay cover isn't on the right all the time, it varies with each unit. The side without the rubber PS logo is the bay cover.
Yash - Contestar
I just wanted to add that the above is not correct either
My PS3 Super Slim Mdel No. CECH-4004A has the removable PS logo rubber seal on the left side while the HDD is housed behind the right side (with no rubber PS logo seal)
Eoin - Contestar
My p3 just went off it goes on but then it just shut down
Chadley Abrahams - Contestar