Repara tus cosas Comunidad Tienda

Spin Master Boxer Wheel Gears Replacement

Introducción

If Robot fails to move, the gears inside of wheels may need to be replaced. Follow this guide for instructions on how to access and replace gears. This can be applied to both sets of wheels. You will need a Phillips #00 Screwdriver and tweezers.

Qué necesitas

  1. Spin Master Boxer Wheel Gears Replacement, Robot Screen: paso 1, imagen 1 de 1

    • Set Spin Master Boxer on your workspace so that the bottom panel faces upwards.

    Editar

  2. Spin Master Boxer Wheel Gears Replacement: paso 2, imagen 1 de 1

    • Using a Phillips #00 screw driver, unscrew the four 4mm screws in each corner of the bottom panel.

    Editar

  3. Spin Master Boxer Wheel Gears Replacement: paso 3, imagen 1 de 1

    • Carefully remove the bottom panel of the Spin Master Boxer by lifting up, away from the main body of robot.

    Editar

  4. Spin Master Boxer Wheel Gears Replacement: paso 4, imagen 1 de 2 Spin Master Boxer Wheel Gears Replacement: paso 4, imagen 2 de 2

    • While holding onto the axels of the wheels, gently pull the top panel of the robot away from its body.

    • Be aware when removing the panel that multiple wires connect it to the body of the Spin Master Boxer.

    Editar

  6. Spin Master Boxer Wheel Gears Replacement: paso 5, imagen 1 de 1

    • Remove the plastic screen from the body of the robot. It should come off easily as it is not attached by anything.

    Editar

  7. Spin Master Boxer Wheel Gears Replacement, Robot Wheel Gears: paso 6, imagen 1 de 1

    • Place robot on back so that the sensors are facing up.

    Editar

  8. Spin Master Boxer Wheel Gears Replacement: paso 7, imagen 1 de 2 Spin Master Boxer Wheel Gears Replacement: paso 7, imagen 2 de 2

    • Gently separate the left set of wheels from the inner portion of the circuit board, by gripping the wheels and pulling them away from main body of robot.

    • There are wires attached to each set of wheels, so be careful not to rip them apart.

    • Repeat the process for the right set of wheels.

    Editar

  9. Spin Master Boxer Wheel Gears Replacement: paso 8, imagen 1 de 2 Spin Master Boxer Wheel Gears Replacement: paso 8, imagen 2 de 2

    • Use the Phillips #00 Screwdriver to remove the 3mm screw that connect the black wheels to the gears.

    • You will have to go through the black wheel to unscrew some of the screws.

    Editar

  10. Spin Master Boxer Wheel Gears Replacement: paso 9, imagen 1 de 3 Spin Master Boxer Wheel Gears Replacement: paso 9, imagen 2 de 3 Spin Master Boxer Wheel Gears Replacement: paso 9, imagen 3 de 3

    • Grip wheel, and gently pull up, to separate white gear casing into its front and back panel.

    Editar

  11. Spin Master Boxer Wheel Gears Replacement: paso 10, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar

    • Using tweezers, grip defective gear, and pull up and out of gear system to replace.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 4 otros colaboradores

Lauren Roide

Miembro Desde 04/16/19

739 Reputación

5 Guías creadas

Insignias: 10

+ 7 más insignias

Equipo

Cal Poly, Team S1-G1, Maness Spring 2019 Miembro de Cal Poly, Team S1-G1, Maness Spring 2019

CPSU-MANESS-S19S1G1

4 Miembros

10 Guías creadas

3 comentarios

This is super useful guide and picture are clear for the steps. Will be excellent to know where to buy these gears replacements?

Javier Perez - Contestar

Hello. Thé motor seems to be broken. Do you Knowles ils spec to buy à New one.

Sorry, im french...

Tanks.

Jerome Carbonneaux - Contestar

Do you know its spec to buy a new one?

Realy sorry...

Jerome Carbonneaux - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 24

Todo El Tiempo: 3,716