Introducción

How to take out the hard drive of the Sony Vaio VGN-S260 laptop

Partes

No se requieren partes.

Flip the laptop over so the Vaio logo is facing down Locate the battery at the top and Find the release and unlock slides on the battery Slide the unlock tab to the unlock position
  • Flip the laptop over so the Vaio logo is facing down

  • Locate the battery at the top and Find the release and unlock slides on the battery

  • Slide the unlock tab to the unlock position

  • Slide the release tab in the direction of the arrow, i.e. towards the unlock tab

Agregar Comentario

With the tabs still in the unlock position, slide the battery away from the main case. With the tabs still in the unlock position, slide the battery away from the main case.
  • With the tabs still in the unlock position, slide the battery away from the main case.

Agregar Comentario

Flip the computer over so the Vaio logo is facedown Unscrew the 2 screws next to the battery
  • Flip the computer over so the Vaio logo is facedown

  • Unscrew the 2 screws next to the battery

Agregar Comentario

Flip the computer over again so the Vaio logo is face up
  • Flip the computer over again so the Vaio logo is face up

  • Open the lid

Agregar Comentario

Press down on the outer gray shell around the keyboard Use the spudger to gently lift keyboard
  • Press down on the outer gray shell around the keyboard

  • Use the spudger to gently lift keyboard

  • Do not pull up the keyboard too far as it is attached to a ribbon underneath

There are 2 spring-held latches, one above the F4 and one above the F12. Push a latch up into the frame of the keyboard, then lift the keyboard gently in that area so the latch doesn't spring back. Then push the other latch and the keyboard will be released.

Yishai Sered - Contestar

Lift up lever underneath the ribbon to detach the keyboard. Lift up lever underneath the ribbon to detach the keyboard.
  • Lift up lever underneath the ribbon to detach the keyboard.

Agregar Comentario

Remove memory/wireless compartment cover
  • Remove memory/wireless compartment cover

Agregar Comentario

Flip so the Vaio Logo is face down Locate and remove a total of 8 screws on the bottom. Locate and remove a total of 8 screws on the bottom.
  • Flip so the Vaio Logo is face down

  • Locate and remove a total of 8 screws on the bottom.

There are 2 more screws on the bottom, one in the middle of the front next to the flash stick socket, and one under the memory door.

Yishai Sered - Contestar

Find and remove 5 screws (they all have arrows next to them) from cover
  • Find and remove 5 screws (they all have arrows next to them) from cover

Agregar Comentario

Flip the laptop over so the Vaio logo is face up Use the spudger to pop up the upper casing Do not lift too much as the Uppercasing is attached to wires underneath
  • Flip the laptop over so the Vaio logo is face up

  • Use the spudger to pop up the upper casing

  • Do not lift too much as the Uppercasing is attached to wires underneath

  • Remove the wires that are attaching the uppercasing to the motherboard

There are also 5 screws from the top of the uppercasing.

Yishai Sered - Contestar

The are 4 cables to remove: flat cable for the power and S buttons at top center; flat cable for the touchpad at bottom center; and 2 twisted pairs for the speakers.

The speaker cable socket is very delicate. If all you are getting at is the CPU or the hard drive, it may be enough to disconnect the flat cables and gently rotate the uppercasing shifting it left to allow access to the right-hand side with the CPU fan and the hard drive.

Yishai Sered - Contestar

The top panel has cutouts that allow the cables to be disconnected before the top of the case is removed. The two flat cables are not clamped and can be pulled vertically out of their connectors. The delicate speaker cables are connected to the motherboard with plugs which can be gently levered up out of their sockets.

roberttrevellyan - Contestar

Remove the uppercasing
  • Remove the uppercasing

Agregar Comentario

Locate the screws holding the hard drive casing in place. Remove the screws
  • Locate the screws holding the hard drive casing in place.

  • Remove the screws

Only the 2 bottom red circles have screws. The top two are open holes for screws that come in from the bottom.

Yishai Sered - Contestar

Only the two bottom screws are there. The two top screws are from the bottom and would have been removed to get the uppercasing off.

Yishai Sered - Contestar

Find orange ribbon that is connected to the hard drive.
  • Find orange ribbon that is connected to the hard drive.

  • Find the holder of the ribbon and pop the ribbon off from it

Agregar Comentario

Remove the casing and the orange ribbon
  • Remove the casing and the orange ribbon

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Jeffrey Bryan

Miembro Desde 20/04/10

552 Reputación

11 Guías creadas

Equipo

Cal Poly, Team 16-4, Maness Spring 2010 Miembro de Cal Poly, Team 16-4, Maness Spring 2010

CPSU-MANESS-S10S16G4

4 Miembros

11 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 3

Últimos 7 Días: 8

Últimos 30 Días: 21

Todo El Tiempo: 12,261