Saltar al contenido principal

Sony SRS-XB30 Bluetooth Chip Replacement

Qué necesitas

  1. Sony SRS-XB30 Bluetooth Chip Replacement, Battery: paso 1, imagen 1 de 1
    • To remove the speaker grill, insert the big spudger underneath it in each corner.

    • Work around the edges to pry the grill up and off.

  2. Sony SRS-XB30 Bluetooth Chip Replacement: paso 2, imagen 1 de 2 Sony SRS-XB30 Bluetooth Chip Replacement: paso 2, imagen 2 de 2
    • With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame.

    • This will need to be done on all four sides of the speaker to remove all four panels

    • This requires some effort because the adhesive is sticky.

  3. Sony SRS-XB30 Bluetooth Chip Replacement: paso 3, imagen 1 de 2 Sony SRS-XB30 Bluetooth Chip Replacement: paso 3, imagen 2 de 2
    • Locate the four screws on the now exposed front panel.

    • Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).

  4. Sony SRS-XB30 Bluetooth Chip Replacement: paso 4, imagen 1 de 1
    • Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.

    • Use the same T7 screwdriver head here.

    • Remove each of the four corner screws (15.0 mm long).

  5. Sony SRS-XB30 Bluetooth Chip Replacement: paso 5, imagen 1 de 1
    • With a little force, carefully lift the lid of the speaker.

    • Make sure that you do not pull on the wires.

  6. Sony SRS-XB30 Bluetooth Chip Replacement: paso 6, imagen 1 de 3 Sony SRS-XB30 Bluetooth Chip Replacement: paso 6, imagen 2 de 3 Sony SRS-XB30 Bluetooth Chip Replacement: paso 6, imagen 3 de 3
    • Unclip the four wire connectors (that are attached to the speaker lid).

    • Disconnect the thin yellow wire (attached to the speaker lid) from its port.

  7. Sony SRS-XB30 Bluetooth Chip Replacement: paso 7, imagen 1 de 1
    • Separate the speaker lid from the bottom frame.

    • To prepare the speaker for the next step place the lid parallel to the frame.

  8. Sony SRS-XB30 Bluetooth Chip Replacement: paso 8, imagen 1 de 1
    • Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.

    • Using the screwdriver with bit PH1, unscrew each screw.

  9. Sony SRS-XB30 Bluetooth Chip Replacement: paso 9, imagen 1 de 1
    • Separate the speaker lid entirely from the bottom frame.

  10. Sony SRS-XB30 Bluetooth Chip Replacement: paso 10, imagen 1 de 1
    • Remove the top screw (10 mm).

    • Use the screwdriver with bit T7.

  11. Sony SRS-XB30 Bluetooth Chip Replacement: paso 11, imagen 1 de 2 Sony SRS-XB30 Bluetooth Chip Replacement: paso 11, imagen 2 de 2
    • Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7.

    • There are two screws on the left side of the white box and one to its right.

  12. Sony SRS-XB30 Bluetooth Chip Replacement: paso 12, imagen 1 de 1
    • Slightly lift the white box with all the wires still attached.

  13. Sony SRS-XB30 Bluetooth Chip Replacement: paso 13, imagen 1 de 2 Sony SRS-XB30 Bluetooth Chip Replacement: paso 13, imagen 2 de 2
    • Take the big spudger and pry the black casing up from the circuit box.

  14. Sony SRS-XB30 Bluetooth Chip Replacement: paso 14, imagen 1 de 1
    • Locate the blue film attached to the circuit box containing the charging port.

    • Detach the blue film from the box.

  15. Sony SRS-XB30 Bluetooth Chip Replacement: paso 15, imagen 1 de 1
    • Detach the yellow, black and red wires by pulling them directly up.

  16. Sony SRS-XB30 Bluetooth Chip Replacement: paso 16, imagen 1 de 2 Sony SRS-XB30 Bluetooth Chip Replacement: paso 16, imagen 2 de 2
    • Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.

  17. Sony SRS-XB30 Bluetooth Chip Replacement, Bluetooth Chip: paso 17, imagen 1 de 1
    • To save time, pry up and remove the top panel first.

  18. Sony SRS-XB30 Bluetooth Chip Replacement: paso 18, imagen 1 de 2 Sony SRS-XB30 Bluetooth Chip Replacement: paso 18, imagen 2 de 2
    • Take the spudger and pry under the plastic square that the Bluetooth chip is directly attached to.

    • This will separate the plastic square from the lid.

  19. Sony SRS-XB30 Bluetooth Chip Replacement: paso 19, imagen 1 de 1
    • Remove the Bluetooth chip.

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Un comentario

I'm pretty sure this is the nfc chip and not the Bluetooth chip

john may - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 16

Ultimos 30 días: 56

Todo El Tiempo: 3,445