Repara tus cosas Comunidad Tienda

Sony Reader Touch Edition PRS-600 Motherboard Replacement

Qué necesitas

  1. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Back Panel: paso 1, imagen 1 de 1

    • Using the Phillips head screwdriver PH000, remove the two 1.4 mm screws that are located on the backside of the device.

    Editar

  2. Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 2, imagen 1 de 1

    • Slide the back cover off by pushing it to the left, away from the side that held the screws.

    • Remove the cover.

    Editar

  3. Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 3, imagen 1 de 1

    • This is what the device should look like once the back cover panel has been removed.

    Editar

  4. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Battery: paso 4, imagen 1 de 1

    • Once the back cover has been removed locate the battery in the bottom right corner of the device.

    • Using the pointed end of the spudger, push out the white plug that is connected to the battery from its beige base.

    Editar

  6. Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 5, imagen 1 de 1

    • Use the flat end of the spudger to pry the battery out of its holder. There may be glue holding it in place.

    Editar

  7. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Inner Casing: paso 6, imagen 1 de 1

    • Using a screwdriver remove the four 1.4 mm screws that are holding the black plastic casing in place.

    Editar

  8. Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 7, imagen 1 de 1

    • Pry open the black casing to access the screw that is holding down the battery holder.

    • Remove the one 1.4 mm screw that is holding down the battery holder located under black casing.

    • Lift the black inner casing and the battery holder out of the device.

    • The battery holder and the black inner casing are connected by a thin strip of copper. There may be glue holding the black inner casing in place.

    Editar

  9. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Motherboard: paso 8, imagen 1 de 1

    • Using a Phillips head screwdriver, remove the one 1.4 mm screw holding in the motherboard.

    Editar

  10. Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 9, imagen 1 de 2 Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 9, imagen 2 de 2

    • Using the flat end of the spudger, flip up the 4 latches holding down the thin, orange strips that connect the motherboard to the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports.

    • To disconnect the the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports pull each orange slip away from their corresponding latch.

    Editar

  11. Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 10, imagen 1 de 2 Sony Reader Touch Edition PRS-600 Motherboard Replacement: paso 10, imagen 2 de 2

    • Lift the end of the motherboard closest to the memory cards and pull out.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Terrika Ngobili

Miembro Desde 10/13/14

857 Reputación

7 Guías creadas

Insignias: 11

+ 8 más insignias

Equipo

Clemson, Team 1-4, Benson Fall 2014 Miembro de Clemson, Team 1-4, Benson Fall 2014

CLEM-BENSON-F14S1G4

4 Miembros

22 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 3

Ultimos 30 días: 12

Todo El Tiempo: 623