Repara tus cosas Comunidad Tienda

Shark Ultimate Professional Mode Display Replacement

Introducción

Before beginning this guide, ensure that the device is both unplugged and cool; failure to do so may result in electrocution or burns.

Qué necesitas

  1. Shark Ultimate Professional Mode Display Replacement, Mode Display: paso 1, imagen 1 de 3 Shark Ultimate Professional Mode Display Replacement, Mode Display: paso 1, imagen 2 de 3 Shark Ultimate Professional Mode Display Replacement, Mode Display: paso 1, imagen 3 de 3

    • Use the Philips head #0 screwdriver to remove the two 11.49mm screws at the back of the iron.

    • Remove the back cover piece.

    • Make sure the iron is unplugged and cooled off.

    Editar

  2. Shark Ultimate Professional Mode Display Replacement: paso 2, imagen 1 de 2 Shark Ultimate Professional Mode Display Replacement: paso 2, imagen 2 de 2

    • Use the Philips head #0 screwdriver to remove the two 11.77mm screws holding the white clamp to the iron.

    • Use the Philips head #0 screwdriver to remove the two 6.58mm screws holding the black wires to the body of the iron.

    • Removing the left black wire will also free the red wire, attached by the same screw.

    Editar

  3. Shark Ultimate Professional Mode Display Replacement: paso 3, imagen 1 de 3 Shark Ultimate Professional Mode Display Replacement: paso 3, imagen 2 de 3 Shark Ultimate Professional Mode Display Replacement: paso 3, imagen 3 de 3

    • Pull the split end of the power cord upward through the ball joint of the iron.

    • Set aside the power cord.

    Editar

  5. Shark Ultimate Professional Mode Display Replacement: paso 4, imagen 1 de 3 Shark Ultimate Professional Mode Display Replacement: paso 4, imagen 2 de 3 Shark Ultimate Professional Mode Display Replacement: paso 4, imagen 3 de 3

    • Use the Philips head #0 screwdriver to remove remaining 6.58mm screws that hold a wire on the bottom (brown and blue).

    • Unscrew from left to right.

    • Wires order (from left to right): Brown, Blue, Black, Red

    • Unclip the black adapter piece on the bottom right.

    Editar

  6. Shark Ultimate Professional Mode Display Replacement: paso 5, imagen 1 de 2 Shark Ultimate Professional Mode Display Replacement: paso 5, imagen 2 de 2

    • Use the Philips head #0 screwdriver to remove two 9.75mm screws (left and right) affixed to circuit board.

    Editar

  7. Shark Ultimate Professional Mode Display Replacement: paso 6, imagen 1 de 2 Shark Ultimate Professional Mode Display Replacement: paso 6, imagen 2 de 2

    • Use the Philips head #0 screwdriver to remove the two 9.82mm screws (left and right) from the white border on top of the circuit board.

    • Pull the circuit board out from its affixed position.

    Editar

  8. Shark Ultimate Professional Mode Display Replacement: paso 7, imagen 1 de 3 Shark Ultimate Professional Mode Display Replacement: paso 7, imagen 2 de 3 Shark Ultimate Professional Mode Display Replacement: paso 7, imagen 3 de 3

    • Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle.

    • Remove and set aside the mode display.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 4 otros colaboradores

Drew Carff

Miembro Desde 10/23/17

868 Reputación

5 Guías creadas

Insignias: 14

+ 11 más insignias

Equipo

USF Tampa, Team S1-G4, Leahy Fall 2017 Miembro de USF Tampa, Team S1-G4, Leahy Fall 2017

USFT-LEAHY-F17S1G4

3 Miembros

10 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 4

Todo El Tiempo: 645