Skip to main content

Introducción

Of all the parts to replace on the Shark Pro Steam Pocket Mop, the heating element is likely the trickiest to replace since it's at the core of the mop. Nonetheless, this guide will make the process a breeze. As always, before doing any disassembly on your Shark Professional Steam Pocket Mop, make sure to unplug the mop and empty the water tank for your safety.

  1. Unwrap the power cord from the handle. Remove the 56.0 mm Phillips head #2 screw located above the water tank cap.
    • Unwrap the power cord from the handle.

    • Remove the 56.0 mm Phillips head #2 screw located above the water tank cap.

    • Pull the handle to separate it from the body.

  2. Remove the three 12.0 mm Phillips head #2 screws where the handle connects to the body. Remove the plastic cap. Remove the plastic cap.
    • Remove the three 12.0 mm Phillips head #2 screws where the handle connects to the body.

    • Remove the plastic cap.

  3. Remove the three 16.0 mm T10 Torx screws near the top of the body and remove the water tank cap. The third screw is directly on other side of the bottom screw in the photo.
    • Remove the three 16.0 mm T10 Torx screws near the top of the body and remove the water tank cap.

    • The third screw is directly on other side of the bottom screw in the photo.

  4. Remove steam control button cover with a metal spudger. Remove the two 12.0 mm Phillips head #2 screws underneath. Remove the plastic rim with clear plastic cover.
    • Remove steam control button cover with a metal spudger.

    • Remove the two 12.0 mm Phillips head #2 screws underneath.

    • Remove the plastic rim with clear plastic cover.

  5. Remove the Shark logo decal on the front of body using a metal spudger. Remove the two 12.0 mm Phillips head #2 screws underneath. Pull out the plastic cover to remove.
    • Remove the Shark logo decal on the front of body using a metal spudger.

    • Remove the two 12.0 mm Phillips head #2 screws underneath.

    • Pull out the plastic cover to remove.

  6. Pop off the grey front plate to expose the control panel and screws necessary to open mop body.
    • Pop off the grey front plate to expose the control panel and screws necessary to open mop body.

  7. Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora

    Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora
  8. Remove the three 12.0 mm Philips head #2 screws connected to the dark grey plastic trim.
    • Remove the three 12.0 mm Philips head #2 screws connected to the dark grey plastic trim.

  9. Remove the four 16.0 mm T10 Torx screws located on the back of the mop.
    • Remove the four 16.0 mm T10 Torx screws located on the back of the mop.

  10. Remove the two 12.0 mm Phillips head #2 screws that hold the power cord to the device.
    • Remove the two 12.0 mm Phillips head #2 screws that hold the power cord to the device.

  11. Pop off the dark grey plastic trim cover.
    • Pop off the dark grey plastic trim cover.

  12. Pop open the white plastic mop body by pulling apart from the front and back side.
    • Pop open the white plastic mop body by pulling apart from the front and back side.

  13. Remove the four 12.0 mm Phillips head #2 screws on the sides of the heating element.
    • Remove the four 12.0 mm Phillips head #2 screws on the sides of the heating element.

  14. Pull out the heating element and use precision tweezers or pliers to pinch and loosen the two clamps. Remove both tubes from the heating element.
    • Pull out the heating element and use precision tweezers or pliers to pinch and loosen the two clamps.

    • Remove both tubes from the heating element.

  15. Grip each wire at its base and pull to disconnect them from the heating element.
    • Grip each wire at its base and pull to disconnect them from the heating element.

  16. Remove two 12.0 mm Phillips head #2 screws from the heating element.
    • Remove two 12.0 mm Phillips head #2 screws from the heating element.

  17. Pull apart wire connectors to fully detach the heating element.
    • Pull apart wire connectors to fully detach the heating element.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Brett Wilson

Miembro Desde 12/02/18

848 Reputación

6 Guías creadas

Equipo

USF Tampa, Team S15-G1, Boczar Spring 2018 Miembro de USF Tampa, Team S15-G1, Boczar Spring 2018

USFT-BOCZAR-S18S15G1

4 Miembros

7 Guías creadas

Is the heating element available somewhere? I cannot find it anywhere.

Mark Cashion - Contestar

Añadir comentario

Ver Estadísticas:

Past 24 Hours: 0

Past 7 Days: 6

Past 30 Days: 32

Global: 769