Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

This repair may be necessary if the brush roll is not spinning. The belt is tight on the roll and may require some force to remove it.

  1. Open the garage door by sliding both of the release buttons away from you. Lift off the garage door.
    • Open the garage door by sliding both of the release buttons away from you.

    • Lift off the garage door.

  2. Remove the plastic screw covering using a metal spudger by pushing the sharp side into the crevice and prying the cover out. Remove the plastic screw covering using a metal spudger by pushing the sharp side into the crevice and prying the cover out.
    • Remove the plastic screw covering using a metal spudger by pushing the sharp side into the crevice and prying the cover out.

  3. Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw. Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw.
    • Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw.

  4. Use the iFixit Opening Tool to pry the side of the vacuum open.
    • Use the iFixit Opening Tool to pry the side of the vacuum open.

  5. Remove the side component with your hands.
    • Remove the side component with your hands.

  6. Remove old the belt from the two gears by prying it off using the metal spudger. The new belt will be very tight and difficult to put back on. In order to reinstall, start with the belt on one gear, then slowly rotate the other gear, pushing on the belt and allowing it to catch the teeth.
    • Remove old the belt from the two gears by prying it off using the metal spudger.

    • The new belt will be very tight and difficult to put back on. In order to reinstall, start with the belt on one gear, then slowly rotate the other gear, pushing on the belt and allowing it to catch the teeth.

  7. Repeat on the other side of the vacuum.
    • Repeat on the other side of the vacuum.

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Equipo

Cal Poly, Team S17-G5, White Fall 2018 Miembro de Cal Poly, Team S17-G5, White Fall 2018

CPSU-WHITE-F18S17G5

4 Miembros

14 Guías creadas

Thanks… Would have taken me forever to figure out how to get to the belts…!!!

Mike Babb - Contestar

Wonderful directions and a great help, thanks. However one important factor was left out, the part number for the belts.

Dave Orr - Contestar

Where to get the carpet brush belt? What would the belt size be?

Silver Dominator - Contestar

Add me to the rest. I also want a belt. Does anybody ever respond to these questions?

I’m hopeful we can find a source

ShellyB

shellyb -

Just been told by shark that you cant buy the belt in the UK and you have to buy the whole new head at £60!

What a rip off! Wont be buying a Shark again!

graemefromhaworth - Contestar

When you say buy a new head does that mean the whole floor unit

Thomas - Contestar

They made me buy a whole new motorized head for $99 last year. Just the duo roller doesn’t spin making it harder to push around. I still have the broken head so I think I want to take it apart and see if it’s just the belt. The new head cracked by the rear right wheel so maybe I can Frankenstein a good working one.

Keith Sauer - Contestar

I have a shark rocket duo clean. I'm confused. Will have to wait if Shark will help?when i ring them. Pulling the foot apart seen to be allot of work if you don't just to be to the belt not knowing what you are doing or buy a new vacuum foot . Wish life was made easier

lowe.m - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 36

Ultimos 7 días: 244

Ultimos 30 días: 1,115

Todo El Tiempo: 19,977