Repara tus cosas Comunidad Tienda

Sceptre X9 Komodo VII Video Motherboard Replacement

Qué necesitas

  1. Sceptre X9 Komodo VII Video Motherboard Replacement, Stand: paso 1, imagen 1 de 1

    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

    Editar

  2. Sceptre X9 Komodo VII Video Motherboard Replacement: paso 2, imagen 1 de 1

    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

    Editar

  3. Sceptre X9 Komodo VII Video Motherboard Replacement, Board Cover: paso 3, imagen 1 de 1

    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

    Editar

  5. Sceptre X9 Komodo VII Video Motherboard Replacement: paso 4, imagen 1 de 3 Sceptre X9 Komodo VII Video Motherboard Replacement: paso 4, imagen 2 de 3 Sceptre X9 Komodo VII Video Motherboard Replacement: paso 4, imagen 3 de 3

    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

    Editar

  6. Sceptre X9 Komodo VII Video Motherboard Replacement: paso 5, imagen 1 de 2 Sceptre X9 Komodo VII Video Motherboard Replacement: paso 5, imagen 2 de 2

    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

    Editar

  7. Sceptre X9 Komodo VII Video Motherboard Replacement, Video Motherboard: paso 6, imagen 1 de 3 Sceptre X9 Komodo VII Video Motherboard Replacement, Video Motherboard: paso 6, imagen 2 de 3 Sceptre X9 Komodo VII Video Motherboard Replacement, Video Motherboard: paso 6, imagen 3 de 3

    • Use caution when removing the connectors as they can easily break when removing.

    • Disconnect the multi-pin connector at the top of the board by firmly grasping the connector and pulling to the side.

    • Disconnect the multi-pin connector that runs between the video motherboard and the power supply motherboard. Firmly grasp the connector and pull straight up.

    • A plastic opening tool can be used to assist in the removal of connectors.

    Editar

  8. Sceptre X9 Komodo VII Video Motherboard Replacement: paso 7, imagen 1 de 2 Sceptre X9 Komodo VII Video Motherboard Replacement: paso 7, imagen 2 de 2

    • Remove the two 3/16" hex head screws from the VGA connecter. Use a pair of needle nose pliers if a wrench is not available.

    Editar

  9. Sceptre X9 Komodo VII Video Motherboard Replacement: paso 8, imagen 1 de 1

    • Remove the four 6.4mm #2 Phillips screws from the corners of the motherboard with a #2 Phillips screwdriver.

    Editar

  10. Sceptre X9 Komodo VII Video Motherboard Replacement: paso 9, imagen 1 de 2 Sceptre X9 Komodo VII Video Motherboard Replacement: paso 9, imagen 2 de 2

    • Lift the motherboard straight up to remove it from the back panel.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 2 otros colaboradores

David Taylor

Miembro Desde 09/26/12

10 Reputación

1 Guía escrita

Insignias: 6

+ 3 más insignias

Equipo

Cal Poly, Team 16-56, Forte Fall 2012 Miembro de Cal Poly, Team 16-56, Forte Fall 2012

CPSU-FORTE-F12S16G56

5 Miembros

13 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 2

Todo El Tiempo: 632