Repara tus cosas Comunidad Tienda

Sceptre X9 Komodo VII Speakers Replacement

Qué necesitas

  1. Sceptre X9 Komodo VII Speakers Replacement, Stand: paso 1, imagen 1 de 1

    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

    Traducir

  2. Sceptre X9 Komodo VII Speakers Replacement: paso 2, imagen 1 de 1

    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

    Traducir

  3. Sceptre X9 Komodo VII Speakers Replacement, Board Cover: paso 3, imagen 1 de 1

    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

    Traducir

  5. Sceptre X9 Komodo VII Speakers Replacement: paso 4, imagen 1 de 3 Sceptre X9 Komodo VII Speakers Replacement: paso 4, imagen 2 de 3 Sceptre X9 Komodo VII Speakers Replacement: paso 4, imagen 3 de 3

    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

    Traducir

  6. Sceptre X9 Komodo VII Speakers Replacement: paso 5, imagen 1 de 2 Sceptre X9 Komodo VII Speakers Replacement: paso 5, imagen 2 de 2

    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

    Traducir

  7. Sceptre X9 Komodo VII Speakers Replacement, Speakers: paso 6, imagen 1 de 1

    • Disconnect the two connectors to the speakers by gently pulling on the hard plastic straight up.

    Traducir

  8. Sceptre X9 Komodo VII Speakers Replacement: paso 7, imagen 1 de 1

    • Carefully peel the tape from the board.

    Traducir

  9. Sceptre X9 Komodo VII Speakers Replacement: paso 8, imagen 1 de 1

    • Flip the monitor so the screen is facing you.

    • Using Phillips #2 screwdriver remove the four 6.25 mm screws securing the speakers:

    Traducir

  10. Sceptre X9 Komodo VII Speakers Replacement: paso 9, imagen 1 de 1

    • Carefully lift the speakers up.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 3 otros colaboradores

Xenia Leon Rodriguez

Miembro Desde 09/26/12

37 Reputación

1 Guía escrita

Insignias: 4

+1 mas insignia

Equipo

Cal Poly, Team 16-56, Forte Fall 2012 Miembro de Cal Poly, Team 16-56, Forte Fall 2012

CPSU-FORTE-F12S16G56

5 Miembros

13 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 394