Saltar al contenido principal

Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement

Qué necesitas

  1. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement, Screen: paso 1, imagen 1 de 2 Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement, Screen: paso 1, imagen 2 de 2
    • Apply the heat gun around the edges of the tablet to melt the adhesive glue.

    • Do not allow the gun to remain still for more than two seconds, so that you do not melt the plastic around the screen.

    • If you do not have access to a heat gun, you may also use an iOpener or a hair dryer. Refer to the iOpener guide for extra help.

  2. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 2, imagen 1 de 2 Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 2, imagen 2 de 2
    • Apply the suction to the bottom or top right corner.

    • Use the plastic opening tool at several points around the screen while the suction is being applied to pop the screen out.

  3. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 3, imagen 1 de 1
    • Once the screen is detached, open the tablet like a book.

    • Gently open the tablet, and do not pull the pieces apart since you can risk damaging the orange ribbon cable.

  4. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 4, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar
    • Using the precision tweezers, remove the silver tape that is holding the orange ribbon cable connecting the two pieces.

  5. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 5, imagen 1 de 1
    • Using the precision tweezers, remove the small press-fit connector from the body of the tablet.

  6. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement, Screws: paso 6, imagen 1 de 2 Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement, Screws: paso 6, imagen 2 de 2
    • Using the Philips #000 screwdriver, remove the seventeen 2.74 mm screws around the edges.

    • Remove the two 2.74 mm black screws in the middle of the tablet with the Philips #000 screwdriver.

    • Put the screws on a magnetic project mat or in a container so that you do not lose them.

  7. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 7, imagen 1 de 3 Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 7, imagen 2 de 3 Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 7, imagen 3 de 3
    • Take the plastic opening tool around the tablet to remove the motherboard from the device.

  8. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement, Headphone Jack: paso 8, imagen 1 de 2 Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement, Headphone Jack: paso 8, imagen 2 de 2
    • Locate the headphone jack towards the bottom right-hand side.

    • Using the plastic opening tool, lift up the press-fit connector.

  9. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 9, imagen 1 de 1
    • Using the Phillips #000 Screwdriver, remove the 2.74 mm black screw next to the headphone jack.

  10. Samsung Galaxy Tab S2 9.7 AT&T Headphone Jack Replacement: paso 10, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar
    • Using the precision tweezers, remove the headphone jack.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Joy Harris

Miembro Desde 02/15/17

814 Reputación

7 Guías creadas

Equipo

USF Tampa, Team S3-G4, Sullivan Spring 2017 Miembro de USF Tampa, Team S3-G4, Sullivan Spring 2017

USFT-SULLIVAN-S17S3G4

3 Miembros

14 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 6

Ultimos 30 días: 12

Todo El Tiempo: 774