Saltar al contenido principal

Introducción

If you are having issues with keeping a charge or your battery is dead, use this guide to properly replace the battery in your Samsung Galaxy Tab A 10.1.

Resumen del Video

  1. Samsung Galaxy Tab A 10.1 Battery Replacement, Back Panel: paso 1, imagen 1 de 2 Samsung Galaxy Tab A 10.1 Battery Replacement, Back Panel: paso 1, imagen 2 de 2
    • Have the front of the device facing you.

    • Begin near one of the curved edges of the device (see photo two for visual example).

    • Place a plastic opening tool between the front and back panels.

    • If a plastic opening tool doesn’t work, using a metal spudger may work, but it may damage the plastic on the device.

    • Remember to remove the micro SD card (if present) before you begin.

  2. Samsung Galaxy Tab A 10.1 Battery Replacement: paso 2, imagen 1 de 2 Samsung Galaxy Tab A 10.1 Battery Replacement: paso 2, imagen 2 de 2
    • Once the plastic opening tool is fully inserted, wedge it around the device’s edges to separate the panels.

    • Lift the back panel off of the device.

    • The back panel will make a clicking noise while being lifted off of the device.

  3. Samsung Galaxy Tab A 10.1 Battery Replacement, Disconnecting the battery: paso 3, imagen 1 de 1
    • Remove the adhesive film and flip up the retaining flap on the ZIF battery connector.

    • Slide the orange battery ribbon cable out of the ZIF connector.

  4. Samsung Galaxy Tab A 10.1 Battery Replacement: paso 4, imagen 1 de 2 Samsung Galaxy Tab A 10.1 Battery Replacement: paso 4, imagen 2 de 2
    • Remove the adhesive film, lift the retaining tab and withdraw the white speaker ribbon.

  5. Samsung Galaxy Tab A 10.1 Battery Replacement: paso 5, imagen 1 de 3 Samsung Galaxy Tab A 10.1 Battery Replacement: paso 5, imagen 2 de 3 Samsung Galaxy Tab A 10.1 Battery Replacement: paso 5, imagen 3 de 3
    • Lift the retaining tab and withdraw the black LCD ribbon.

  6. Samsung Galaxy Tab A 10.1 Battery Replacement, Battery removal: paso 6, imagen 1 de 2 Samsung Galaxy Tab A 10.1 Battery Replacement, Battery removal: paso 6, imagen 2 de 2
    • Using a Phillips #000 screwdriver, remove the ten 4 mm screws around the battery.

    • Slide a plastic opening tool under the bottom of the battery close to the speakers and lift up.

    • The large rectangular white and black piece is the entire battery. Be careful not to puncture it.

Conclusión

To reassemble your device, follow these instructions in reverse order.

41 personas más completaron esta guía.

Isabella Li

Miembro Desde 02/10/17

2,248 Reputación

7 Guías creadas

Equipo

Cal Poly, Team S15-G6, Livingston Fall 2017 Miembro de Cal Poly, Team S15-G6, Livingston Fall 2017

CPSU-LIVINGSTON-F17S15G6

4 Miembros

26 Guías creadas

7 comentarios

Used this guide up until the disconnecting of the battery in order to fix the black screen of death. Very very helpful. Thank you.

Steffan Syd Apel - Contestar

If you have my kind of bad luck — where the latch for the battery flex cable connector sticks to the tape when you remove the tape, and then it will not snap back into place — don’t worry about it too much, because the connector tension will hold the flex cable in place. Just put the tape back over the top as directed.

Richard Ekblaw - Contestar

Why does it say you need a heat gun?

Geert Pante - Contestar

To loosen the adhesive. A hair dryer works well too

qaisraja22 -

how to calibrate the new battery?

when device switched off due to 0% of battery - there is impossible to boot it even with charging. there is required to open a tablet and charge the battery from another source.

Алексей Хейдоров - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 17

Ultimos 7 días: 176

Ultimos 30 días: 742

Todo El Tiempo: 50,101