Saltar al contenido principal

Samsung Galaxy Tab 2 10.1 Battery Disconnect

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. Samsung Galaxy Tab 2 10.1 Battery Disconnect, Back Cover: paso 1, imagen 1 de 2 Samsung Galaxy Tab 2 10.1 Battery Disconnect, Back Cover: paso 1, imagen 2 de 2
    • The plastic opening tool may break during this step. You may need to use the heavy duty spudger instead.

    • Insert the plastic opening tool between the glass screen and the back cover so the curved end of the plastic opening tool is under the glass. Gently pry the back cover away from the glass screen.

    • Be sure to lift the entire display from the body and that you are not are lifting the glass from the display. You will need to reach down a little further for the correct removal.

    • Continue inserting the plastic opening tool around the whole device screen to completely separate the back cover from the glass screen.

    Note that the headphone port protrudes into the back cover framing. Hence the rest of the back needs to be unclipped and taken off first.

    Levi Howard - Contestar

    I had problems getting it to separate at first. Pushing down with my thumb on the very edge of the case from the front while pushing up with my fingers from the back flexed it enough to get a very small jeweler’s screwdriver in the gap. From there I worked it until I could get the little bread wrapper plastics clips in the space. When it needed something stronger a 1 or 2 inch plastic putty knife from Walmart did the trick.

    William H Bowers - Contestar

    I replaced the battery and nothing no screen nothing. the batt was 3.7 V though.

    The old one had 0V. I might have messed up the ribbon cables?

    I put back the cover on it.

    Held on the power button for 10 seconds, nothing. Held the power button and the volume up button for 10 seconds… also nothing..

    I am leaving it charge for a while now. Even though if your battery is like full (3.7V measured) it should come on… but nothing..

    Lets wait and see. Or this will be garbage…

    xbox40489 - Contestar

  2. Samsung Galaxy Tab 2 10.1 Battery Disconnect: paso 2, imagen 1 de 2 Samsung Galaxy Tab 2 10.1 Battery Disconnect: paso 2, imagen 2 de 2
    • Gently lift the screen up with your finger.

    • If the screen will not separate from the back cover, try repeating step 1.

  3. Samsung Galaxy Tab 2 10.1 Battery Disconnect, Battery Disconnect: paso 3, imagen 1 de 1
    • Using your fingers, remove the green tape covering the battery connector.

  4. Samsung Galaxy Tab 2 10.1 Battery Disconnect: paso 4, imagen 1 de 3 Samsung Galaxy Tab 2 10.1 Battery Disconnect: paso 4, imagen 2 de 3 Samsung Galaxy Tab 2 10.1 Battery Disconnect: paso 4, imagen 3 de 3
    • Insert the flat end of the heavy-duty spudger between the wires and underneath the battery connector. Carefully lift the black battery connector up to disconnect it from the motherboard.

    • The metal spudger shown in the photo is not recommended due to the possibility of an electrical short. Use an ESD-safe tool, such as a heavy-duty (nylon) spudger.

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Daniel Rostom

Miembro Desde 02/02/15

822 Reputación

2 Guías creadas

2 comentarios

Disconnected the battery, checked the contacts, reconnected it. As soon as I reconnected the battery I could smell and feel heat from the two silver areas on the MB (guessing RAM/Processors are under there). Still doesn't turn on. Any ideas?

Glenn G - Contestar

Those pictures are of a Galaxy Note, T-8013, not a Tab 2.

Brian Clancy - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 5

Todo El Tiempo: 3,041