Saltar al contenido principal

Samsung Galaxy Note8 Reemplazo de Batería

Qué necesitas

  1. Samsung Galaxy Note8 Reemplazo de Batería, Tapa trasera: paso 1, imagen 1 de 1
    • Apaga tu teléfono.

    • Prepara un iOpener para suavizar el adhesivo en la parte trasera de la Note8.

    • Aplica el iOpener atrás de la Note8 a lo largo del lado con el botón de encendido.

    I used a heat gun to soften the glue - worked it around the edges, moving the heat gun quickly. As this is my first attempt, I’m still calibrating on this - but other guides mention getting the back cover hot enough so as it’s just too hot to touch. I also have a temp probe on my multi-meter, and I measured appx. 75 deg. C.

    One of the other guides showed using a electronics hot plate set to 105 deg C for 60 sec.

    Phil Brooks - Contestar

  2. Samsung Galaxy Note8 Reemplazo de Batería: paso 2, imagen 1 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 2, imagen 2 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 2, imagen 3 de 3
    • Usa una ventosa de succión para levantar la cubierta trasera y un lengüeta o punzón plástico para entrar en la abertura.

    • Dado que la cubierta trasera también está ligeramente curvada en los bordes, debes insertar la lengüeta o punzón plástico en un ángulo inferior desde abajo.

    • Empieza en la parte media de lado y corte el adhesivo mientras levanta la cubierta con la ventosa de succión.

    • Ten cuidado de no presionar demasiado con la lengüeta o punzón plástico para evitar quebrar la cubierta trasera. En vez de eso, jala con la ventosa de succión y usa la lengüeta o punzón para cortar el adhesivo.

    • Mueve la lengüeta o punzón hacia la esquina inferior y déjela allí para evitar que el adhesivo vuelva a sellarse en la carcasa.

    • Utiliza otra lengüeta o punzón y deslízalo hacia la esquina superior.

    • Si al deslizar la legüeta o punzón se vuelve más difícil podrías necesitar calentar el iOpener y aplicarlo nuevamente a la cubierta trasera.

    I used an X-acto knife with the flat blade to get it started. I tried using the suction cup - but it’s difficult to get good leverage. Once I got the cover started - I used the metal pry tool (sharpened with a dremel file) and a business card to work it open.

    This is definitely the hardest part.

    Phil Brooks - Contestar

    Once off I see all the glue on the curved part of the chassis NOTON THE BACK. Apply heat to curved edges.

    Lyle Walsh - Contestar

  3. Samsung Galaxy Note8 Reemplazo de Batería: paso 3, imagen 1 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 3, imagen 2 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 3, imagen 3 de 3
    • Nuevamente toma otra lengüeta o punzón plástico y cuidadosamente muévelo hacia la esquina y a lo largo del borde.

    • Recalienta la cubierta trasera con un iOpener de ser necesario.

    • Deja la lengüeta o punzón plástico en la esquina superior para que el adhesivo no se adhiera nuevamente.

  4. Samsung Galaxy Note8 Reemplazo de Batería: paso 4, imagen 1 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 4, imagen 2 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 4, imagen 3 de 3
    • Rota el dispositivo y comienza a separar el adhesivo de la parte inferior con otra lengüeta o punzón plástico.

    • Deja una lengüeta o punzón plástico en la esquina inferior derecha para evitar que el adhesivo se adhiera nuevamente.

  5. Samsung Galaxy Note8 Reemplazo de Batería: paso 5, imagen 1 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 5, imagen 2 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 5, imagen 3 de 3
    • Cuando el adhesivo ha sido separado apropiadamente en tres lados podrás levantar lentamente la cubierta trasera.

    • No fuerces la apertura. Utilice un iOpener nuevamente para suavizar el adhesivo si la cubierta trasera no se desprende o empieza a doblarse.

    • Presta atención al conector del sensor de la huella dactilar al abrir la cubierta trasera. Necesitarás desconectarlo como se describe en el siguiente paso.

    I broke the back camera cover for the NUT 8 and then I bought a commercial cover and installed it but the quality of the picture became very bad and my question is, do you know where to get the original cover at a reasonable price?

    Loord Mohammad - Contestar

  6. Samsung Galaxy Note8 Reemplazo de Batería: paso 6, imagen 1 de 1
    • Utiliza un par de pinzas para desconectar el sensor de la huella dactilar.

    • Es posible que el conector se haya desconectado al abrir la cubierta trasera.

    don't skip disconnecting the sensor, even if isn't still glued to the case. it has to move away from the NFC/charging coil assembly in order to free the latter so it can be lifted away from the battery.

    a nonni mouse - Contestar

  7. Samsung Galaxy Note8 Reemplazo de Batería: paso 7, imagen 1 de 1
    • Remueve la tapa trasera.

    • Para preparar el re-ensamblaje remueve cualquier resto de adhesivo del teléfono y limpia las áreas con pegamento con alcohol isopropílico y un paño sin pelusa.

    How do you swap the fingerprint sensor

    Lukus Carr - Contestar

    You can use a tweezer to swap the fingerprint sensor, you might be careful when doing the step 6, additionally, a tweezer will be helpful when reassemble the fingerprint sensor. please note that your new back cover needs to have the fingerprint adhesive on. most of the product did not have. i have get a LUVSS brand from amazon which came with all OEM adhesive and full set tools, even a B6000 glue, best option to go for replacing the note 8 back glass

    ggmall - Contestar

  8. Samsung Galaxy Note8 Reemplazo de Batería, Ensamblaje de bobina de carga y antena NFC: paso 8, imagen 1 de 1
    • Remueve los diez tornillos Phillips #00.

  9. Samsung Galaxy Note8 Reemplazo de Batería: paso 9, imagen 1 de 2 Samsung Galaxy Note8 Reemplazo de Batería: paso 9, imagen 2 de 2
    • Ingresa una púa de apertura en el borde superior entre el ensamblaje de la bobina de carga y la antena NFC y la caja.

    • Levanta la parte superior del ensamblaje de la caja.

    Solve the problem of moisture during charging

    moaed aljnapy - Contestar

  10. Samsung Galaxy Note8 Reemplazo de Batería: paso 10, imagen 1 de 1
    • Con cuidado saca el ensamblaje completo de la antena NFC y bobina de carga.

    • La parte izquierda inferior del ensamblaje está pegado ligeramente al marco.

  11. Samsung Galaxy Note8 Reemplazo de Batería, Desconexión de la batería: paso 11, imagen 1 de 1
    • Usa el extremo plano de un spudger para desconectar el conector de la batería.

  12. Samsung Galaxy Note8 Reemplazo de Batería, Batería: paso 12, imagen 1 de 1
    • Prepara un iOpener y coloca sobre la pantalla por al menos dos minutos para soltar el adhesivo debajo de la batería. Recaliente y coloque nuevamente el iOpener las veces que sea necesario.

    • Alternativamente o cuando la batería esté inflada, puedes aplicar un poco de alcohol isopropílico bajo cada una de las esquinas de la batería y permita que el alcohol penetre durante varios minutos para ayudar a debilitar el adhesivo.

    Isopropyl alcohol worked great but flooded the main board and took all night to dry out

    Lyle Walsh - Contestar

  13. Samsung Galaxy Note8 Reemplazo de Batería: paso 13, imagen 1 de 2 Samsung Galaxy Note8 Reemplazo de Batería: paso 13, imagen 2 de 2
    • Usa la parte plana de un spudger para levantar la batería desde la esquina superior derecha.

    • Estarás haciendo palanca contra la carcasa, directamente sobre la tarjeta principal. Levanta cuidadosamente para evitar dañar algún componente cercano.

    • Podrías necesitar recalentar y reaplicar el iOpener repetidamente para suavizar aún más el adhesivo. El adhesivo es resistente y podría tomar algunos intentos para que el calibrador logre entrar bajo la batería.

    • Usa el calibrador para levantar la batería hasta que puedas insertar una lengüeta plástica para evitar que el adhesivo se adhiera nuevamente.

    • Trata en lo posible de no deformar la batería durante este proceso. Las baterías de cubierta-suave de iones de litio podrían gotear químicos peligrosos, prenderse fuego o inclusive explotar si se daña. No utilices fuerza excesiva o realices palanca a la batería con objetos metálicos.

    I really think this is much less risky if you just take out the motherboard. There is much less risk to heat the other components when you are loosening the battery adhesive and you can be more rough when getting the battery out. Especially (but not exclusively) if you are changing the screen anyway. Should be after step 29.

    Additionally, I went at the battery from the side with a credit card and prying out the battery evenly across the length of the battery. I was even able to make a ‘ridge-peek’ from the card and screen and heat it from above while pushing down on the card and prying at eh same time. I got it out without any battery deformation. I would get one of those flat credit card shaped tools if I did it again because the credit card deformed and I had to keep flipping it.

    tobinmckenna - Contestar

    Didn’t need to heat or use alcohol to get the battery out - just gently kept prying. I used the metal pry tool that came with the battery replacement tool kit. But very careful not to puncture the old battery.

    Phil Brooks - Contestar

  14. Samsung Galaxy Note8 Reemplazo de Batería: paso 14, imagen 1 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 14, imagen 2 de 3 Samsung Galaxy Note8 Reemplazo de Batería: paso 14, imagen 3 de 3
    • Utiliza la parte plana del spudger para generar palanca sobre la esquina superior izquierda de la batería donde el cable flexible se encuentra.

    • Desliza el spudger a lo largo del lateral de la batería para cortar el adhesivo restante.

    • Cuando hagas palanca procura mantenerse en las áreas naranjas. Evita el área roja en el medio se encuentra la parte trasera de la pantalla.

  15. Samsung Galaxy Note8 Reemplazo de Batería: paso 15, imagen 1 de 1
    • Retira la batería fuera de la carcasa.

    • No reutilices una batería después de haber sido removida, hacer esto representa un peligro potencial a su seguridad. Reemplaza con una batería nueva.

    • Retira cualquier residuo de adhesivo del teléfono y limpia las áreas con pegamento con alcohol isopropílico y un paño libre de pelusas.

    • Consulta esta guía para colocar adhesivos nuevos para la batería.

    • Consulta esta guía para colocar adhesivos nuevos y cortados a medida.

    do you mean when replacing display the battery should also be replaced?

    John Kenneth - Contestar

    Hi John,

    Since you can replace the display without removing the battery, you do not need to replace the battery.

    Arthur Shi -

    Great guide!

    Quick note. If you are changing out the back cover or cant get touch ID reconnected Warm it up some on the back cover. It should pop right off with a spudger. Then reattach it inside the phone. Make sure the adhesive on back cover is sticky enough to hold it in place. Then set back cover on top!

    jake765111 - Contestar

Conclusión

Asegura la nueva batería con adhesivo pre-cortado o cinta adhesiva de doble cara. Para colocarlo correctamente, aplica el nuevo adhesivo en el teléfono en los lugares donde se encontraba el adhesivo antiguo, no directamente en la batería. Presiona la batería firmemente en su lugar durante 5-10 segundos.

Para volver a ensamblar tu dispositivo, sigue las instrucciones en orden inverso. Aplica nuevo adhesivo donde sea necesario.

Si es posible, enciende tu teléfono y prueba tu reparación antes de cerrar y sellar el teléfono.

Para mejores resultados, cuando termines tu reparación, calibra tu batería recién instalada.

68 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Tobias Isakeit

Miembro Desde 03/31/14

116,683 Reputación

188 Guías creadas

Equipo

Master Techs Miembro de Master Techs

Community

322 Miembros

2,506 Guías creadas

10 comentarios

Awesome fix. Do you have anything for the front glass replacements by chance? I want to do both at the same time

Rick Moore - Contestar

For those wondering how to apply the replacement adhesive, there is a video on the iFixit YouTube channel about installing adhesive on Samsung devices. Its a bit generic, but it points you in the right direction.

Christopher Zibbell - Contestar

Hi Christopher,

I’ve edited the last step to include some adhesive guides! Hope that helps!

Arthur Shi -

Thanks!! Very good detail. I was able to get the back cover off and replace the battery - the phone is working like a champ!

Phil Brooks - Contestar

Would it be possible to augment the mAh? instead of 3300 mAh giving a little bit more power?

William Houli - Contestar

I think there is a 3rd party manufacturer who sells 3600mAh instead of 3300 so I guess yes.

Amiyo Paul -

How do you PUT IT BACK TOGETHER? especially the fingerprint scanner part?

Titan Rock - Contestar

The fingerprint can be a tricky maneuver! Align the connector carefully over the socket, and use your finger or the flat end of a spudger to press it in place. It may take a few tries. Patience is key!

Arthur Shi -

Does any one know how undo what I did after following above instructions to replace battery?

I see some dead pixel and cracked back panel :(

Ahmed Shaik - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 14

Ultimos 7 días: 172

Ultimos 30 días: 866

Todo El Tiempo: 97,276