Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Use this guide to replace the back cover of your Galaxy Note8.

If your battery is swollen, do not heat your phone. If needed, you can use a dropper or syringe to inject isopropyl alcohol (90+%) around the edges of the back cover to weaken the adhesive. Swollen batteries can be very dangerous, so wear eye protection and exercise due caution, or take it to a professional if you're not sure how to proceed.

Opening the phone will damage the waterproof sealing. If you do not replace the adhesive seals, your phone will function normally, but will loose water-protection.

You will probably need replacement adhesive to reattach the back cover.

  1. Switch off your phone.
    • Switch off your phone.

    • Prepare an iOpener for softening the adhesive on the back of the Note8.

    • Apply the iOpener on the back of the Note8 along the side with the power button.

    I used a heat gun to soften the glue - worked it around the edges, moving the heat gun quickly. As this is my first attempt, I’m still calibrating on this - but other guides mention getting the back cover hot enough so as it’s just too hot to touch. I also have a temp probe on my multi-meter, and I measured appx. 75 deg. C.

    One of the other guides showed using a electronics hot plate set to 105 deg C for 60 sec.

    Phil Brooks - Contestar

  2. Use a suction handle to lift the back cover and an opening pick to get in the gap. Since the back cover is also slightly curved at the edges you want to insert the opening pick at a lower angle from underneath. Start at the middle of the side and cut the adhesive while pulling up with the suction handle.
    • Use a suction handle to lift the back cover and an opening pick to get in the gap.

    • Since the back cover is also slightly curved at the edges you want to insert the opening pick at a lower angle from underneath.

    • Start at the middle of the side and cut the adhesive while pulling up with the suction handle.

    • Be careful not to lever the opening pick too much to avoid breaking the back cover. Rather pull with the suction handle and use the pick for cutting the adhesive.

    • Move the pick towards the bottom corner and leave it there to keep the adhesive from resealing to the case.

    • Use another pick and move it to the top corner.

    • If it's getting harder to move the pick you might need to reheat the iOpener and apply it to the back cover again.

    I used an X-acto knife with the flat blade to get it started. I tried using the suction cup - but it’s difficult to get good leverage. Once I got the cover started - I used the metal pry tool (sharpened with a dremel file) and a business card to work it open.

    This is definitely the hardest part.

    Phil Brooks - Contestar

  3. Again take another opening pick and carefully move it around the corner and along the top edge. Reheat with an iOpener if necessary. Leave the pick at the top right corner to keep the adhesive from resealing.
    • Again take another opening pick and carefully move it around the corner and along the top edge.

    • Reheat with an iOpener if necessary.

    • Leave the pick at the top right corner to keep the adhesive from resealing.

  4. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación
  5. Rotate the device and start to separate the adhesive at the bottom with another opening pick. Leave the pick at the bottom right corner to keep the adhesive from resealing. Leave the pick at the bottom right corner to keep the adhesive from resealing.
    • Rotate the device and start to separate the adhesive at the bottom with another opening pick.

    • Leave the pick at the bottom right corner to keep the adhesive from resealing.

  6. When the adhesive has been separated on all three sides properly you will be able to slowly lift the back cover. Don't force it open. Use an iOpener to again soften the adhesive if the back cover won't come off or starts to bend. Pay attention to the fingerprint sensor connector when flipping the back cover open. You might need to disconnect it as described in the next step.
    • When the adhesive has been separated on all three sides properly you will be able to slowly lift the back cover.

    • Don't force it open. Use an iOpener to again soften the adhesive if the back cover won't come off or starts to bend.

    • Pay attention to the fingerprint sensor connector when flipping the back cover open. You might need to disconnect it as described in the next step.

    I broke the back camera cover for the NUT 8 and then I bought a commercial cover and installed it but the quality of the picture became very bad and my question is, do you know where to get the original cover at a reasonable price?

    Loord Mohammad - Contestar

  7. Use a pair of tweezers to disconnect the fingerprint sensor.
    • Use a pair of tweezers to disconnect the fingerprint sensor.

    • The connector might already have come off when flipping the back cover open.

  8. Remove the back cover.
    • Remove the back cover.

    • To prepare for the reassembly remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

    How do you swap the fingerprint sensor

    Lukus Carr - Contestar

    You can use a tweezer to swap the fingerprint sensor, you might be careful when doing the step 6, additionally, a tweezer will be helpful when reassemble the fingerprint sensor. please note that your new back cover needs to have the fingerprint adhesive on. most of the product did not have. i have get a LUVSS brand from amazon which came with all OEM adhesive and full set tools, even a B6000 glue, best option to go for replacing the note 8 back glass

    ggmall - Contestar

Conclusión

If possible, turn on your phone and test the new part before installing new adhesive and resealing the phone.

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

To reassemble your device, follow these instructions in reverse order.

After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

25 personas más completaron esta guía.

Tobias Isakeit

Miembro Desde 31/03/14

74,169 Reputación

142 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

129 Miembros

13,145 Guías creadas

My adhivsive was a pain in the but! Never fixed a phone that hard glued :O

Vidar G - Contestar

the separate adhesive was unneeded the replacement back cover came with adhesive

Anthony Asp - Contestar

So close!!!!’ I sliced the fingerprint sensor cable off, that area of the back glass was so smashed. Hopefully I can get a replacement to me by Saturday

Douglas Pocknett Jr - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 10

Ultimos 7 días: 104

Ultimos 30 días: 462

Todo El Tiempo: 18,252