Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the end of the stylus and remove it from its slot in the midframe.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the rear case by the corner nearest the divot and remove it from the phone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
-
After the click, release the card and it will pop out of its slot.
-
Remove the microSD card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone.
-
Slide the plastic opening tool down the seam.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to run the plastic opening tool down the seam.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully pry around the corner with a plastic opening tool.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry along the top of the phone with a plastic opening tool.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the plastic opening tool down to free the corner of the midframe from the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Free the clips along the power button side of the phone.
-
Lastly, free the two clips along the top and bottom edge of battery compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to disconnect the vibrator/power button assembly cable connector.
-
Disconnect the antenna cable connector.
-
Disconnect the display cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the front-facing camera cable connector.
-
Disconnect the headphone jack cable connector.
-
Disconnect the digitizer cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the spudger to disconnect the antenna cable connector from the motherboard.
-
Disconnect the soft button cable connector.
-
Disconnect the USB board cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3 mm Phillips #00 screw securing the headphone jack assembly to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the headphone jack portion of the assembly and lift it out of its groove in the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pull the headphone jack straight up without twisting the cable to remove the earpiece speaker portion from its recess.
-
Cancelar: No complete esta guía.
42 personas más completaron esta guía.
5 comentarios
Did you use the miniature hammer for that step David?
Where can I purchase a headphone jack to replace my defective one?
Installed everything correctly. Ear piece works fine, however my headphone jack (which was the faulty component in the first place) does not work at all. The phone does not even detect when I have a pair of earbuds plugged in. I replaced this piece due to heavy static out of the headphone jack.