Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the end of the stylus and remove it from its slot in the midframe.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the rear case by the corner nearest the divot and remove it from the phone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
-
After the click, release the card and it will pop out of its slot.
-
Remove the microSD card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone.
-
Slide the plastic opening tool down the seam.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to run the plastic opening tool down the seam.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully pry around the corner with a plastic opening tool.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry along the top of the phone with a plastic opening tool.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the plastic opening tool down to free the corner of the midframe from the display assembly.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Free the clips along the power button side of the phone.
-
Lastly, free the two clips along the top and bottom edge of battery compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to disconnect the vibrator/power button assembly cable connector.
-
Disconnect the antenna cable connector.
-
Disconnect the display cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the front-facing camera cable connector.
-
Disconnect the headphone jack cable connector.
-
Disconnect the digitizer cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the spudger to disconnect the antenna cable connector from the motherboard.
-
Disconnect the soft button cable connector.
-
Disconnect the USB board cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3 mm Phillips #00 screw securing the headphone jack assembly to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the headphone jack portion of the assembly and lift it out of its groove in the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pull the headphone jack straight up without twisting the cable to remove the earpiece speaker portion from its recess.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3mm Phillips #00 screw from the front-facing camera bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3 mm Phillips #00 screw securing the antenna board to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of a spudger under the antenna board to free it from the adhesive holding it to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently de-route the antenna cable from its channel in the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of a spudger under the vibrator to free it from the adhesive holding it to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to detach the power button from the adhesive securing it to the display assembly.
-
Remove the vibrator/power button assembly from the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 3 mm Phillips #00 from the speaker enclosure.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to disconnect the antenna cable connector from the USB board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the flat end of a spudger under the USB board to separate it from the display assembly.
-
Remove the USB board from the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently deroute the antenna cable from its notch in the display assembly.
-
Remove the antenna cable.
-
Cancelar: No complete esta guía.
183 personas más completaron esta guía.
12 comentarios
This guide is awful. Not even the US phone model. mine and most on youtube does not have the antennae on both side, only a antena on one of the sides of the phone.
Also this does not cover how to remove most things that you HAVE to remove when you buy the digitizer+lcd from here... not to mention that it stops in the middle...
there is a video on youtube from https://www.youtube.com/user/LE55ONS that shows how to dismantle the note2 in much more detail than this... and he goes all the way and show how to remove every piece needed.
thx for the video!
note i was repairing looked slightly different. no antenna on the left and powerbutton/vibrator where differnet parts, midframe is hold by 2 additional tabs inside battery compartment. video was a good addition to this guid, and helped alot ;)
Lego -
Thank you for the link to the videos, it helped particularly for the vibrator and power button.
This is the Sprint model, SPH-L900. It's not his fault that your phone is different.
Roger -
