Saltar al contenido principal

Introducción

Use this guide to replace the midframe on your Samsung Galaxy Note 4.

  1. Insert a fingernail or plastic opening tool into the divot to the left of the rear-facing camera. Gently pry and twist the flexible rear cover off the back of the phone.
    • Insert a fingernail or plastic opening tool into the divot to the left of the rear-facing camera.

    • Gently pry and twist the flexible rear cover off the back of the phone.

  2. Insert a fingernail or plastic opening tool into the recess in the bottom right corner of the battery and lift upward.
    • Insert a fingernail or plastic opening tool into the recess in the bottom right corner of the battery and lift upward.

    • Remove the battery.

  3. Remove the SIM card by first pushing the card slightly out of its housing, then pulling it the rest of the way. Remove the SIM card by first pushing the card slightly out of its housing, then pulling it the rest of the way.
    • Remove the SIM card by first pushing the card slightly out of its housing, then pulling it the rest of the way.

  4. Baterías para ordenadores portátiles

    Un pequeño arreglo para un gran resultado.

    Comprar Ahora

    Baterías para ordenadores portátiles

    Un pequeño arreglo para un gran resultado.

    Comprar Ahora
  5. Remove the sixteen 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
    • Remove the sixteen 4.0 mm Phillips #00 screws securing the midframe to the display assembly.

    • Grasp the cap of the S Pen and remove it from its slot in the midframe.

  6. Insert a plastic opening tool between the midframe and the display assembly. Work the plastic opening tool around the perimeter of the phone to break the adhesive. This adhesive is relatively weak, so no heat gun should be necessary.
    • Insert a plastic opening tool between the midframe and the display assembly.

    • Work the plastic opening tool around the perimeter of the phone to break the adhesive.

    • This adhesive is relatively weak, so no heat gun should be necessary.

    • Be careful to not separate the front glass panel from the rest of the display assembly, as it is still held together with adhesive.

  7. Use a plastic opening tool to loosen the clasps around the battery housing.
    • Use a plastic opening tool to loosen the clasps around the battery housing.

  8. Push on the battery housing to separate the midframe from the display assembly. You will have to apply a reasonable amount of pressure to separate the two parts. If your new midframe does not come with a headphone jack assembly, you'll need to transfer the one from the old midframe into the new one. It can be pried loose with plastic opening tools, as it is held in place with several plastic pins.
    • Push on the battery housing to separate the midframe from the display assembly.

    • You will have to apply a reasonable amount of pressure to separate the two parts.

    • If your new midframe does not come with a headphone jack assembly, you'll need to transfer the one from the old midframe into the new one. It can be pried loose with plastic opening tools, as it is held in place with several plastic pins.

Conclusión

To reassemble your device, follow these instructions in reverse order.

25 personas más completaron esta guía.

Jarrett Corr

Miembro Desde 09/01/15

1,113 Reputación

1 Guía escrita

Equipo

Cal Poly, Team 70-6, Forte Winter 2015 Miembro de Cal Poly, Team 70-6, Forte Winter 2015

CPSU-FORTE-W15S70G6

4 Miembros

15 Guías creadas

I have attempted twice to remove the hear housing without breaking the LCD. And i have been working on phones for 12 years. It will break every time this should not be attempted unless the LCD is already bad.

Ted Jonason - Contestar

its very helpful.much appreciated!

Amirul La Ahad - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 12

Últimos 30 Días: 63

Todo El Tiempo: 25,850