Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

This guide shows how to remove everything from the display assembly.

  1. Insert a fingernail or plastic opening tool in the gap between the rear case and the base of the phone.
    • Insert a fingernail or plastic opening tool in the gap between the rear case and the base of the phone.

  2. Slide your fingernail or plastic opening tool along the edge of the rear case. Lift the case gently from the base.
    • Slide your fingernail or plastic opening tool along the edge of the rear case.

    • Lift the case gently from the base.

    Why... is it not simple enough already lol

    Adam Ahmed - Contestar

  3. Insert a fingernail or plastic opening tool into the small gap between the battery and the phone base. Lift the battery out of its recess.
    • Insert a fingernail or plastic opening tool into the small gap between the battery and the phone base.

    • Lift the battery out of its recess.

  4. Place your fingernail in the groove of the stylus pen.
    • Place your fingernail in the groove of the stylus pen.

    • Pull the stylus pen away from the phone.

  5. Remove the twelve 4mm Phillips #00 screws from the back chassis.
    • Remove the twelve 4mm Phillips #00 screws from the back chassis.

  6. Insert the plastic opening tool into the Stylus Pen placement holder.
    • Insert the plastic opening tool into the Stylus Pen placement holder.

    • Lift the plastic opening tool so that the midframe separates from the base.

  7. Remove the single screw beside headphone jack. Remove the single screw beside headphone jack.
    • Remove the single screw beside headphone jack.

    You can skip this step, it is usseles as this screw doesn’t attach the mother board at all

    Oriol Felisart - Contestar

  8. Use tweezers to remove both antenna clips. Use a spudger to disconnect six cable connectors.
    • Use tweezers to remove both antenna clips.

    • Use a spudger to disconnect six cable connectors.

  9. Pull up on the motherboard with tweezers.
    • Pull up on the motherboard with tweezers.

    Can i change at&t board to 9002 or 9005??,

    Ayyaz - Contestar

    My mother board is not working what should I do I can't use Bluetooth, WiFi,hotspot or insert sim

    soha Javed - Contestar

    My wifi hotspot is not working

    Kiran Thopate - Contestar

  10. Insert the spudger into the headphone jack.
    • Insert the spudger into the headphone jack.

  11. Lift the spudger to separate the jack assembly from the motherboard.
    • Lift the spudger to separate the jack assembly from the motherboard.

    • Pull to remove.

    it remove the jack and the speaker in the same time.

    bangahome - Contestar

  12. Remove the metal bracket located in the top left hand corner.
    • Remove the metal bracket located in the top left hand corner.

    As well as the front camera and sensor up under it.

    Xavier Rodriguez - Contestar

  13. Remove the vibrating motor by pulling up on it carefully with the tweezers.
    • Remove the vibrating motor by pulling up on it carefully with the tweezers.

    toggle the motor on the left, cause you need to remove the start button with the motor in the same time.

    All is paste on the display assembly. Use a screw to pass under the elements, and unglue them.

    bangahome - Contestar

  14. Lift USB port from the front assembly using the tweezers.
    • Lift USB port from the front assembly using the tweezers.

    You need to pull up the USB port and all the blue card.

    Use a screw to pass under the card, beacause everything is paste on the display assembly.

    bangahome - Contestar

    Be VERY careful with the board, or just leave it there.

    In some (I think all) devices, the board is GLUED with the display assembly.

    Maybe to stabilize the port (But they can use screws, right? D*mn nasty glue!).

    Salvator - Contestar

  15. You are now left with the display assembly.
    • You are now left with the display assembly.

    Wonderful description.

    matha studio - Contestar

    It tooks me about an hour to change the display.

    Thanks for this tutorial.

    bangahome - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

144 personas más completaron esta guía.

Brittany Gail

Miembro Desde 23/09/14

8,353 Reputación

8 Guías creadas

Equipo

USF Tampa, Team 2-2, Blackwell Fall 2014 Miembro de USF Tampa, Team 2-2, Blackwell Fall 2014

USFT-BLACKWELL-F14S2G2

4 Miembros

25 Guías creadas

είναι απόλυτα κατανοητό.

chandr - Contestar

Can you just replace the digitizer or is the digitizer glue down to good to the display where it might damage the LCD display when trying to replace the digitizer?

rob lang - Contestar

to safely remove the LCD display from the front touch screen glass w/o damaging the LCD screen I advise you to invest in and familiarize yourself with an LCD Separator machine and all the accessories that go along with it. Also, search for the machine and watch the videos..

tkflenorl - Contestar

Can you just replace the digitizer or is the digitizer glue down to good to the display where it might damage the LCD display when trying to replace the digitizer?

sunil - Contestar

Can you just replace the digitizer or is the digitizer glue down to good to the display where it might damage the LCD display when trying to replace touch

sunil - Contestar

This tutorial is incomplete, for instance the 'vibrator motor' removal does not specifies that this also removes the power button, and the removal of the front camera and light sensor is omitted, and the fact that heating the usb port part is very helpful if not mandatory before lifting it. I followed the video tutorial here which is complete: Samsung Galaxy Note 3 Display Assembly Video Tutorial Replacement

Julien GENEST - Contestar

How do I remove the screen/digitizer/front glass from the display assembly? I have a broken screen and need to install the replacement LCD/digitizer piece I bought, and need to install it into the display assembly before reassembling.

David H - Contestar

How I can replace the wifi and bluetooth part in note?

mohanad - Contestar

warning :

on the new part (display assembly) don’t forget to remove plastic protection on the radiator of cpu !!

Michel BERNARD - Contestar

I have successfully replaced the display with a new display, at which point the power button wasn’t working properly because I didn’t install it properly - fixed that, and I have now noticed that the phone will charge with the back plate on, only, however if I screw the back plate in this stops it from charging. What am I doing wrong?

Jesse - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 31

Ultimos 30 días: 139

Todo El Tiempo: 117,946