Saltar al contenido principal

Introducción

This guide shows how to remove everything from the display assembly.

  1. Insert a fingernail or plastic opening tool in the gap between the rear case and the base of the phone.
    • Insert a fingernail or plastic opening tool in the gap between the rear case and the base of the phone.

  2. Slide your fingernail or plastic opening tool along the edge of the rear case. Lift the case gently from the base.
    • Slide your fingernail or plastic opening tool along the edge of the rear case.

    • Lift the case gently from the base.

  3. Insert a fingernail or plastic opening tool into the small gap between the battery and the phone base. Lift the battery out of its recess.
    • Insert a fingernail or plastic opening tool into the small gap between the battery and the phone base.

    • Lift the battery out of its recess.

  4. Place your fingernail in the groove of the stylus pen.
    • Place your fingernail in the groove of the stylus pen.

    • Pull the stylus pen away from the phone.

  5. Remove the twelve 4mm Phillips #00 screws from the back chassis.
    • Remove the twelve 4mm Phillips #00 screws from the back chassis.

  6. Insert the plastic opening tool into the Stylus Pen placement holder.
    • Insert the plastic opening tool into the Stylus Pen placement holder.

    • Lift the plastic opening tool so that the midframe separates from the base.

  7. Remove the single screw beside headphone jack. Remove the single screw beside headphone jack.
    • Remove the single screw beside headphone jack.

  8. Use tweezers to remove both antenna clips. Use a spudger to disconnect six cable connectors.
    • Use tweezers to remove both antenna clips.

    • Use a spudger to disconnect six cable connectors.

  9. Pull up on the motherboard with tweezers.
    • Pull up on the motherboard with tweezers.

  10. Insert the spudger into the headphone jack.
    • Insert the spudger into the headphone jack.

  11. Lift the spudger to separate the jack assembly from the motherboard.
    • Lift the spudger to separate the jack assembly from the motherboard.

    • Pull to remove.

  12. Remove the metal bracket located in the top left hand corner.
    • Remove the metal bracket located in the top left hand corner.

  13. Remove the vibrating motor by pulling up on it carefully with the tweezers.
    • Remove the vibrating motor by pulling up on it carefully with the tweezers.

  14. Lift USB port from the front assembly using the tweezers.
    • Lift USB port from the front assembly using the tweezers.

  15. You are now left with the display assembly.
    • You are now left with the display assembly.

Conclusión

To reassemble your device, follow these instructions in reverse order.

137 personas más completaron esta guía.

Brittany Gail

Miembro Desde 23/09/14

8,236 Reputación

8 Guías creadas

Equipo

USF Tampa, Team 2-2, Blackwell Fall 2014 Miembro de USF Tampa, Team 2-2, Blackwell Fall 2014

USFT-BLACKWELL-F14S2G2

4 Miembros

25 Guías creadas

είναι απόλυτα κατανοητό.

chandr - Contestar

Can you just replace the digitizer or is the digitizer glue down to good to the display where it might damage the LCD display when trying to replace the digitizer?

rob lang - Contestar

to safely remove the LCD display from the front touch screen glass w/o damaging the LCD screen I advise you to invest in and familiarize yourself with an LCD Separator machine and all the accessories that go along with it. Also, search for the machine and watch the videos..

tkflenorl - Contestar

Can you just replace the digitizer or is the digitizer glue down to good to the display where it might damage the LCD display when trying to replace the digitizer?

sunil - Contestar

Can you just replace the digitizer or is the digitizer glue down to good to the display where it might damage the LCD display when trying to replace touch

sunil - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 9

Ultimos 7 días: 97

Ultimos 30 días: 438

Todo El Tiempo: 112,474