Repara tus cosas Comunidad Tienda

Samsung Galaxy A50 Back Cover Replacement

Introducción

Use this guide to replace the back cover of your Samsung Galaxy A50.

You’ll need replacement adhesive to reattach the back cover when reassembling the device.

Qué necesitas

  1. Samsung Galaxy A50 Back Cover Replacement, Back Cover: paso 1, imagen 1 de 1

    • Start by switching off your phone.

    • Heat an iOpener and apply it to the back cover to soften the adhesive.

    • The adhesive of the Samsung Galaxy A50 is very strong. A hair dryer, heat gun, or hot plate may also be used if you aren't able to open the device with the iOpener. Be careful not to overheat the phone—the AMOLED display and internal battery are both susceptible to heat damage.

    Editar

    Überhitzen das Gerät nicht, das AMOLED-Display und der Akku sind sehr hitzeempfindlich.

    Nur ein kleiner Tippfehler-Hinweis: (Überhitze das Gerät nicht)

    Jonas Hahn - Contestar

    OK, korrigiert. Das kann übrigens jeder machen, iFixit ist ein Wiki.

    VauWeh -

    how long should the heat pack be used for?

    David Hall - Contestar

    The heat pack is in the wrong position in photo - the glue that you are heating is actually all around the edge of the phone!

    David Hall - Contestar

  2. Samsung Galaxy A50 Back Cover Replacement: paso 2, imagen 1 de 3 Samsung Galaxy A50 Back Cover Replacement: paso 2, imagen 2 de 3 Samsung Galaxy A50 Back Cover Replacement: paso 2, imagen 3 de 3

    • Insert an opening pick at the bottom of your phone near the USB-C port.

    • If you can't get between the back cover and midframe with your opening pick, you can use a suction handle or strong tape to pull up the back cover to create a gap.

    • Slide the opening pick to the bottom left corner.

    Editar

    It would be much better to attempt the opening from the top of the phone as there is a delicate flex PCB antenna at the bottom just where you stick the pick in that can get damaged.

    David Hall - Contestar

  4. Samsung Galaxy A50 Back Cover Replacement: paso 3, imagen 1 de 2 Samsung Galaxy A50 Back Cover Replacement: paso 3, imagen 2 de 2

    • Insert a second opening pick and slide it from the bottom to the top left corner to cut the adhesive.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Leave the opening picks in place to prevent the adhesive from resealing.

    Editar

  5. Samsung Galaxy A50 Back Cover Replacement: paso 4, imagen 1 de 3 Samsung Galaxy A50 Back Cover Replacement: paso 4, imagen 2 de 3 Samsung Galaxy A50 Back Cover Replacement: paso 4, imagen 3 de 3

    • Insert a third opening pick under the top left corner of the back cover.

    • Slide the opening pick along the top edge of the phone.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

    Editar

  6. Samsung Galaxy A50 Back Cover Replacement: paso 5, imagen 1 de 3 Samsung Galaxy A50 Back Cover Replacement: paso 5, imagen 2 de 3 Samsung Galaxy A50 Back Cover Replacement: paso 5, imagen 3 de 3

    • Insert a fourth opening pick under the top right corner of the back cover.

    • Slide the tip of the opening pick along the side of the phone to the bottom right corner to cut the adhesive.

    • Leave the opening pick in the bottom right corner to prevent the adhesive from resealing.

    Editar

  7. Samsung Galaxy A50 Back Cover Replacement: paso 6, imagen 1 de 1

    • Remove the back cover.

    • After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

    Editar

    Very straight forward and simple replacement to do with the right tools, I used my hot air gun work station so this might have been alot easier for me then someone without one? Hair dryers work too, just in case a hot airgun station is not available to you dont worry you can do this repair without, but some form of heat will make life alot simpler :)

    Matthew Newton - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.
Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%). Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

15 personas más completaron esta guía.

Autor

con 1 otro colaborador

Adriana Zwink

Miembro Desde 12/18/19

48,076 Reputación

167 Guías creadas

Insignias: 35

+ 32 más insignias

Equipo

iFixit Miembro de iFixit

Staff

135 Miembros

16,734 Guías creadas

Un comentario

Thank you for this write up, I wanted to insure there were no connections and overall it's just something I practice to make sure to double check rather a back cover has any hidden surprises, Trust me I've learned from experience not to Assume anything, lol. Take care, and thanks

Matthew Newton - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 5

Ultimos 7 días: 65

Ultimos 30 días: 259

Todo El Tiempo: 19,463