Introducción

Use this guide to replace your front panel assembly.

  1. Insert a plastic opening tool, or your fingernail, into the opening near the left side of the headphone jack.
    • Insert a plastic opening tool, or your fingernail, into the opening near the left side of the headphone jack.

    • Pry the opening tool downward to pop the rear case from its clips securing it to the the midframe.

    Agregar Comentario

  2. Lift and remove the rear case.
    • Lift and remove the rear case.

    Agregar Comentario

    • Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

    • After the click, release the card and it will pop out of its slot.

    • During reassembly, push the microSD card into the slot until it clicks in place.

    Agregar Comentario

    • Pull the microSD card away from its slot.

    Agregar Comentario

    • Wedge a plastic opening tool into the crevice between the battery and midframe located near the bottom left corner.

    • Push the plastic opening tool downward to pry the battery up from its housing.

    Agregar Comentario

    • Lift and remove the battery from the midframe.

    Agregar Comentario

    • Remove the six 4.0 mm Phillips #00 screws securing the midframe to the front panel assembly.

    Agregar Comentario

    • Unless you pry at the right insertion points, you might have a difficult time removing the midframe. This shot of the display assembly, with display glass facing down, is meant to help you locate them.

      • The first insertion point is a divot to the left of the micro-USB port.

      • The second insertion point is a divot to the right of the micro-USB port near the corner of the phone.

      • The final insertion point is located about two inches to the right of the volume control toggle, toward the corner of the phone. An additional insertion point is located slightly to the right of the volume button if you need it.

    Agregar Comentario

    • Insert a plastic opening tool slightly to the left of the micro-USB port, and pry between the midframe and the display to open a gap.

    Agregar Comentario

  3. GIVE TOOLS. FIX FOREVER.

    GIVE TOOLS.

    FIX FOREVER.

    Spread the Fixmas cheer.

    GIVE TOOLS. FIX FOREVER.

    Spread the Fixmas cheer.

    • Wedge a plastic opening tool slightly to the right of the micro-USB port, and pry between the midframe and the display to widen the gap.

    Agregar Comentario

    • Pry again about two inches to the right of the volume control toggles between the midframe and the front panel assembly.

    Agregar Comentario

    • Pull the micro-USB end of the front panel assembly out and away from the midframe and lift up to free it entirely.

    Agregar Comentario

    • Headphone jack/vibrator assembly cable connector

    • Front-facing camera cable connector

    • Digitizer cable connector

    • Display cable connector

    Agregar Comentario

    • Use the flat end of a spudger to disconnect the headphone jack/vibrator assembly cable.

    Agregar Comentario

    • Use the flat end of a spudger to disconnect the front-facing camera cable connector.

    Agregar Comentario

    • Carefully disconnect the digitizer display cable.

    Agregar Comentario

    • Use a spudger to disconnect the display cable connector.

    Agregar Comentario

    • Remove the two 3 mm Phillips #00 screws.

    Agregar Comentario

    • Lift the micro-USB end of the motherboard away from the display assembly and pull it down.

    • Be mindful that you don't snag the motherboard on any cables as you remove it.

    Agregar Comentario

    • The microphone cover fits in a notch and over a small peg in the display assembly, ensure it is well seated before sealing your device.

    • Make sure the microphone cover stays in its slot on the display assembly.

    • When you removed the motherboard, the microphone cover may have remained stuck on the microphone. Put it back in its notch in the display assembly to avoid losing it.

    Agregar Comentario

    • Remove the 2.3 mm Phillips #00 screw securing the front-facing camera bracket to the display assembly.

    Agregar Comentario

    • Remove the front-facing camera bracket from the display assembly.

    Agregar Comentario

    • Using a pair of tweezers, or your fingers, remove the front-facing camera/earpiece speaker assembly.

    Agregar Comentario

    • Insert the pointed end of a spudger into the gap in the corner of the midframe to free the vibrator from the adhesive.

    • Do not completely remove the vibrator, it is still attached to the headphone jack/vibrator assembly and can only come out with the rest of the unit.

    Agregar Comentario

    • Use the flat end of a spudger to release the headphone jack from the adhesive securing it to the midframe.

    Agregar Comentario

    • Remove the headphone jack/vibrator assembly from the display assembly.

    Agregar Comentario

    • Front panel assembly remains.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

17 personas más completaron esta guía.

Sam Lionheart

Miembro Desde 18/10/12

344,963 Reputación

535 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

114 Miembros

7,278 Guías creadas

My display is broken but the touch screen still works. How do you replace the display?

atworktom - Contestar

I attempted to replace the display glass alone on a Virgin Mobile Galaxy SII, and was unsuccessful. Removing the Glass from the Digitizer proved to be extremely difficult. It seems as if the Virgin Mobile version of the SII is not meant for repair, so easily.

Edward Weissbard - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 1

Últimos 30 Días: 5

Todo El Tiempo: 18,997