Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Introducción

Show user how to install a new micro USB port into device.

  1. Slide your fingernail along the edge of the device and pull at the plastic backing.
    • Slide your fingernail along the edge of the device and pull at the plastic backing.

    • While pulling the plastic backing apart from the device, you will hear a snap sound which signals that the backing has detached.

  2. Pull at the plastic backing gently to remove it after hearing the snap sound.
    • Pull at the plastic backing gently to remove it after hearing the snap sound.

  3. Remove the battery from the device by pulling the battery edge upwards.
    • Remove the battery from the device by pulling the battery edge upwards.

  4. Locate the memory card on the upper right-hand corner of the device.
    • Locate the memory card on the upper right-hand corner of the device.

    • Remove the memory card from the device by gently sliding it out of its holder with your fingers.

  5. Kits de Reparación de Pantalla LCD de iPhone

    La opción de presupuesto, cubierta por nuestra garantía de por vida.

    Compra kits

    Kits de Reparación de Pantalla LCD de iPhone

    Reduce los costos de reparación, no la calidad.

    Compra kits
  6. Remove the seven screws from the back of the phone using the Phillips #000 screwdriver. Separate the backing from the silver trim around the phone by using a nylon spudger to pry between the two components.
    • Remove the seven screws from the back of the phone using the Phillips #000 screwdriver.

    • Separate the backing from the silver trim around the phone by using a nylon spudger to pry between the two components.

    • While separating the two components, most of the buttons (including the power button) will fall out.

  7. Remove the power button using tweezers if it did not fall out in the previous step. At this point, you can replace the power button with a new one from a manufacturer.
    • Remove the power button using tweezers if it did not fall out in the previous step.

    • At this point, you can replace the power button with a new one from a manufacturer.

  8. Remove the white cable along the right side of the device (next to the battery housing) using the nylon spudger.
    • Remove the white cable along the right side of the device (next to the battery housing) using the nylon spudger.

    • Pull out both ends of the white cable. They will easily snap out of place without excessive tension.

    • Do not rip the white cables out of the device.

  9. Remove the screw holding the antenna assembly in place using a Tri-Point Y0 screwdriver. Snap the antenna assembly out of the device gently using your fingers.
    • Remove the screw holding the antenna assembly in place using a Tri-Point Y0 screwdriver.

    • Snap the antenna assembly out of the device gently using your fingers.

  10. Pry the flex cable from the top of the phone by carefully using a nylon spudger. Repeat this step for the larger flex cable located on the left side of the device below the smaller one.
    • Pry the flex cable from the top of the phone by carefully using a nylon spudger.

    • Repeat this step for the larger flex cable located on the left side of the device below the smaller one.

  11. Lift and remove the motherboard from the device.
    • Lift and remove the motherboard from the device.

    • The USB port is located at the top of the motherboard. At this point, replace the port with a new one from a manufacturer.

Conclusión

To reassemble your device, follow these instructions in reverse order.

8 personas más completaron esta guía.

Equipo

Cal Poly, Team 24-25, Regan Fall 2012 Miembro de Cal Poly, Team 24-25, Regan Fall 2012

CPSU-REGAN-F12S24G25

4 Miembros

7 Guías creadas

My phone doesn’t have a memory card. At least, not that I can see. What should I do?

Joshua Campbell - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 3

Todo El Tiempo: 2,186