Saltar al contenido principal

Introducción

If your remote control buttons are no longer working effectively, this guide will show you how to replace the buttons on your remote.

Partes

No se especificaron partes.

  1. Flip the remote over so that the buttons are facing down and the end with the wrist strap is nearest your right hand.
    • Flip the remote over so that the buttons are facing down and the end with the wrist strap is nearest your right hand.

    Thank You ! I needed some help getting the back off. I was getting so upset and found this site. The back wouldn't come off but watched this and got it off. YA me ! Not a handy person.?

    Linda Walker - Contestar

  2. Press and hold the black tab above the battery compartment. While holding down the tab with your left hand, slide down the battery compartment cover with your right hand to remove it.
    • Press and hold the black tab above the battery compartment.

    • While holding down the tab with your left hand, slide down the battery compartment cover with your right hand to remove it.

    Is the black tab also the mute button?

    J-Lyn Estrella - Contestar

  3. Remove the batteries by placing a finger on one end of the battery and pushing downward while pulling the battery out.
    • Remove the batteries by placing a finger on one end of the battery and pushing downward while pulling the battery out.

  4. Unscrew one 7 mm Phillips #0 screw from the center of the battery compartment. Unscrew one 7 mm Phillips #0 screw from the center of the battery compartment.
    • Unscrew one 7 mm Phillips #0 screw from the center of the battery compartment.

  5. Gently pry open the remote using the plastic opening tool. Gently pry open the remote using the plastic opening tool.
    • Gently pry open the remote using the plastic opening tool.

  6. Separate the top and bottom of the remote casing. Gently place each half of the remote onto a table so that the exteriors are face down.
    • Separate the top and bottom of the remote casing.

    • Gently place each half of the remote onto a table so that the exteriors are face down.

    • The remote buttons, sensors, and motherboard are not attached to anything inside the remote. Take apart the remote with caution to ensure these components do not accidentally fall out.

  7. Carefully flip over the front casing side of the remote so that the buttons drop onto the table.
    • Carefully flip over the front casing side of the remote so that the buttons drop onto the table.

    • If the buttons do not drop immediately, use your fingers to peal them off the front casing of the remote.

    This article helps me to replace the Roku remote baterry. Thanks lot.

    Katherine Melinda - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Equipo

Cal Poly, Team 15-2, Livingston Fall 2016 Miembro de Cal Poly, Team 15-2, Livingston Fall 2016

CPSU-LIVINGSTON-F16S15G2

3 Miembros

6 Guías creadas

4 comentarios

Do you have a source for getting replacement buttons? I have volume buttons that don't work and was hoping to fix them/ replace them. Thank you!

Patrick Canady - Contestar

Hi Patrick,

I literally just finished successfully fixing my volume-up button.

The replacement part number for the right microswitches is EVQ-P7J01P, available at Digi-Key:

https://www.digikey.com/product-detail/e...

Really inexpensive (around 30 cents each). Pro-tip - to help remove the old switch easily, cut it in half with sharp side-cutters.

Good luck!

Jeff T.

J Thomson -

Where can I find a component layout?

Rey De Castro - Contestar

Setuproku provides support for all roku related issue. This article help us to understand the Roku remote control.

setuproku code - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 11

Ultimos 30 días: 65

Todo El Tiempo: 4,500