Introducción

This guide will help you remove the safety latch for the container lid.

  1. Twist the plastic lid counterclockwise to unlock it.
    • Twist the plastic lid counterclockwise to unlock it.

    • Lift the lid to remove it from the container.

    Agregar Comentario

  2. Carefully remove the blade from the container.
    • Carefully remove the blade from the container.

    • For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

    Agregar Comentario

    • With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

    Agregar Comentario

    • Use your fingers to pry out the two rubber feet from the bottom cover of the base.

    • The two feet furthest from the button tower contain screws. The other two feet do not.

    Agregar Comentario

    • Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

    • Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

    Agregar Comentario

    • Firmly lift the bottom cover off of the base.

    Agregar Comentario

  3. GIVE TOOLS. FIX FOREVER.

    GIVE TOOLS.

    FIX FOREVER.

    Spread the Fixmas cheer.

    GIVE TOOLS. FIX FOREVER.

    Spread the Fixmas cheer.

    • Remove the smaller white gear by lifting it up with your hand.

    Agregar Comentario

    • Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

    • Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

    • Continue turning the gear until completely removed from the blade-shaft.

    Agregar Comentario

    • Use your hand to firmly pull the blade-shaft from the base.

    Agregar Comentario

    • Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

    Agregar Comentario

    • Unwind power cord from the base pegs.

    Agregar Comentario

    • Use the plastic opening tool to pry open the base from the main body.

    • These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.

    • Once freed, lift the base panel from the main body and set it aside.

    Agregar Comentario

    • Use a Phillips #2 screwdriver to remove the three 9.53-mm screws from inside the main body.

    • Next, turn the device upright and lift the upper casing from around the button gently.

    Agregar Comentario

    • Remove the button by simply pulling it up.

    • Don't lose the spring under the button! Without it, the blender will not function.

    Agregar Comentario

    • Use the Phillips #2 screwdriver to remove one 9.53-mm screw.

    Agregar Comentario

    • Remove the white latch by unhooking it from the spring wire and gently lifting straight up.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Roxanne

Miembro Desde 17/10/13

507 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 4-29, Amido Fall 2013 Miembro de Cal Poly, Team 4-29, Amido Fall 2013

CPSU-AMIDO-F13S4G29

4 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 5

Todo El Tiempo: 1,213