Repara tus cosas Comunidad Tienda

Ring Stick Up Cam Camera Replacement

Introducción

In this guide, we will show you how to replace the camera in a Ring Stick Up Cam. You will need a Phillips #00 screwdriver and a plastic opening tool.

Qué necesitas

  1. Ring Stick Up Cam Camera Replacement, Battery: paso 1, imagen 1 de 1

    • Remove the six 6mm Phillips #00 screws from the back of the device.

    Editar

  2. Ring Stick Up Cam Camera Replacement: paso 2, imagen 1 de 1

    • Pry off the aluminum plate using a plastic opening tool.

    Editar

  3. Ring Stick Up Cam Camera Replacement: paso 3, imagen 1 de 1

    • Remove the two 6mm Phillips #00 screws that were under the aluminum plate.

    Editar

  4. Ring Stick Up Cam Camera Replacement: paso 4, imagen 1 de 1

    • Pry off the back cover using a plastic opening tool.

    Editar

  5. Ring Stick Up Cam Camera Replacement: paso 5, imagen 1 de 1

    • Disconnect the battery power leads using a plastic opening tool.

    Editar

  7. Ring Stick Up Cam Camera Replacement: paso 6, imagen 1 de 1

    • Use a plastic opening tool to loosen the adhesive holding the battery in place and remove the battery by hand.

    Editar

  8. Ring Stick Up Cam Camera Replacement, Camera: paso 7, imagen 1 de 1

    • Remove the three silver 6mm Phillips #00 screws holding the motherboard in the device.

    Editar

  9. Ring Stick Up Cam Camera Replacement: paso 8, imagen 1 de 1

    • Disconnect the ribbon connector shown in the photo.

    Editar

  10. Ring Stick Up Cam Camera Replacement: paso 9, imagen 1 de 1

    • Remove the motherboard from the device by hand.

    Editar

  11. Ring Stick Up Cam Camera Replacement: paso 10, imagen 1 de 1

    • Remove the two black 5mm Phillips #00 screws holding the camera board into the device.

    • Remove the single silver 10mm Phillips #00 screw holding the camera board into the device.

    Editar

  12. Ring Stick Up Cam Camera Replacement: paso 11, imagen 1 de 1

    • Remove the three plastic spacers shown in the photo by hand.

    Editar

  13. Ring Stick Up Cam Camera Replacement: paso 12, imagen 1 de 1

    • Carefully disconnect the camera board from the daughterboard by sliding a plastic opening tool between the camera board and the daughterboard.

    Editar

  14. Ring Stick Up Cam Camera Replacement: paso 13, imagen 1 de 1

    • Lift the camera board out of the housing using your hand.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 3 otros colaboradores

Ao Li

Miembro Desde 02/06/19

245 Reputación

1 Guía escrita

Insignias: 7

+ 4 más insignias

Equipo

UC Davis, Team S18-G3, Lore Winter 2019 Miembro de UC Davis, Team S18-G3, Lore Winter 2019

UCD-LORE-W19S18G3

3 Miembros

8 Guías creadas

2 comentarios

Where can I purchase a new lens?

Javier Casas - Contestar

Any ideas where to get a new lens?

Mete Doguoglu - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 14

Ultimos 30 días: 41

Todo El Tiempo: 4,454